[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
hello there
i am using segger embedded studio with my nrf52 dk, i was trying a soft device example from the sdk 15, everything is working properly, but i see in seggar there...
Hi ,
I am using NINA-B301 EVK having nRF52480 core chipset. I am trying to flash all USB, UART examples to see the log or print on the putty prompt but I am not able to...
Hi,
I am working on a project which involves a number of low power nodes 4-16+ distributed over a relatively large area. There is one client which wants to retrieve data...
Hi. I am tinkering with BLE settings, and changed NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 7.
I then get a 0x04 error code on this function after building and running the...
I am now based on nrf52832 SDK14.2 development, nrf52832 as a peripheral device, I want to connect with IOS phone, nrf52832 provides HID Service, but when connected with Android...
I am experiencing the following compiler error:
In file included from ../../../integration/nrfx/legacy/nrf_drv_uart.c:41:0: ../../../integration/nrfx/legacy/nrf_drv_uart...
I have some question about nRF52832 Bluetooth Firmware upgrade problem:
1. I have a device with nRF52832 in my hand. If I don't use the JTag interface, how can I confirm...
Hi,
We are using Nrf51 with SDK nRF5_SDK_12.3.0_d7731ad
We based a UART bridge on the BLE_APP_UART example
The UART connectivity is Rx/ x only (RX_PIN_NUMBER 0; TX_PIN_NUMBER...
Hi,
we've noticed that after performing an OTA DFU, the Bluetooth Address of the device changes as follows: new_address = old_address - 1
Example: Address before OTA DFU...
Hi there,
I am a beginner to the nRF series and I had the following question.
For a battery powered system, is it better to run the nRF52840 at a lower voltage such...
Hello,
i'm trying to program on 51422. The BLE signal,which runs well on 51DK, doesn't trigger any signal on my own PCB. i've successfully light the LED on my PCB. i think...
Hi,
I'm using nRF52832 and I'm trying to switch from SDK15.0 to SDK 15.2. While I've been able to install micro-ecc library in SDK15.0 and use OTA DFU, somehow I'm stuck...
Hello.
I want to integrate UART and SPI ,I am using SDK15.2. The problem here is i am not able to add app_uart.h to main.c(spi).
My question here is how to add it to main...
My working platform is nRF52-DK, and I want to execute DFU firmware upgrade
1. How to create a Bootloader Image? Which Source-Code of SDK_15_2 is used to build the bootloader...
