Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Is the nrf52832 developer kit compatible with Arduino Leonardo? I know that most Arduino shields work well with Leonardo, but a few have troubles.
Thanks
Hi,
I would like to have a recommended supplier for the 32MHz crystal. I have seen the specification for the crystal. But from my experience it is a bit more complex than...
I followed the guide of this and when I opened the project " BLE_Gateway" ,it showed that the "spi_slave.c","softdevice_handle.c"and "ble_advdata.c" file couldn't be found...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
I have a fully working project that uses the HomeKit SDK 1.0.0 from Nordic Semiconductor.
In order to be compliant with Apple specs I am trying to upgrade to version 2.0...
Hello,
I enabled debugging in keil v5 for the nrf 52 and I am debugging through UART for the ble_app_proximity and viewing the messages in putty. The messages i received...
hello everyone,
I was trying to turn off nrf51822 on some condition. So i thought i will use systemoff mode register to do that.i am attaching code snippet of what i am doing...
I am trying to build the ble_app_hrs using gcc. It seems to build okay. I can program it to the device. When I press button 0 or any of the buttons the leds does nt light...
Hey All,
Just trying to get some advice/examples on how to incorporate notifications into a Custom Service on a nrf51 Dk board using gatts. I have found a couple of examples...
Hallo everyone. I'm working with the processor nRF51422 with S210 softdevice and I would like to ask you if it's possible to drive results of LPCOMP to a General-purpose I...
My goal to build a device that can connect to phone with nRF8001.
I am using nRf8001 Development kit. My prototype uses TI msp430 with the nRF270 board in the kit, and I...
Hello,
I am using a Windows 7 VM (VirtualBox). I can flash my NRF51 DK using nRF Go Studio just fine.
When I open the Master Control Panel (3.10.0.14), I can see the device...
Where can I find a description of the different nRF24 part numbers? Specifically, I am interested in learning which part numbers correspond to OTP variants. Thanks!
