GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi,
using nrf connect SDK v3.1.1
using nrf54L15 development board.
I have been trying to return set uart in low power mode and resume uart low power from a button press...
Hi, I interfaced the Quectel EC200U GSM module with the nrf5340dk. Now I want to do the FOTA with the help of GSM . Is there any example documents or any experince. And also...
I am trying to make the nrf9161 go to very low power mode for 10 seconds and then come back online.
Actually I would not mind if it were to start all over again when coming...
Hello,
I am using the example on the Nordic DK to get UDP messages from the Hologram API to the Nordic Modem. AT#XUDPSVR=1,6002 #XUDPSVR: 3,"started" OK
I very inconsistently...
Hello,
I am working with the nRF9151 board and trying to read SIM/eSIM information.
Steps I followed:
Used nRF Programmer → Erase all.
Opened Board Configuration ...
Dear Nordic
We are evaluating a wearable device and plan to use nRF54H20 be our MCU,
Since our device will be a small form factor and Nordic not released datasheet yet...
Hi, I'm working on nRF9151 on custom board, NCS 3.1.0 and I'm building application with TF-M enabled. I've encountered quite a strange problem. If I remove all UART instances...
Hi,
using nrf sdk connect 3.1.1
using nRF54L15-PDK evaluation board.
Steps to reproduce issue:
1. Setup my board into low power. my branch mark is ~2.9uA.
2. Perform...
I use BLE for one-to-many connections. Usually, the peripheral device should first broadcast, then establish the connection for communication, and finally disconnect. However...
Hi there! I am trying to set up external flash (w25q64) with my NRF52840 project over SPI. I have adapted the spi_flash sample in an attempt to set up this device, but I am...
Hello,
We are developing a product based on the nRF54L15, using BT Mesh. We also use the FLPR. For communication between the cores, we use ICMSG.
Separately, ICMSG and...
Hello!
I am completely new to embedded development and i am becoming quite desperate.
I have ordered a custom board which has an nrf52840 chip on it and a vl53l1cxvofy1...
I am using the nPM1300 MIKROE Click board with an ESP32 over TWI (I2C) . I am facing an issue when VDDIO is sourced from VOUT2 using the onboard VDDIO_SEL jumper .
Although...
I have an odd issue with an older nRF52840-DK, I can flash and read memory from the device just fine but no matter what version of NCS I use, it will not execute whatever...
