I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
The thread where it happens is "unknown” despite the fact I name all the threads I create. With addr2line I found that it is zephyr/kernel/timeout.c 56 but it says nothing...
Hi I'm trying to debug the record_text example in the nrf connect sdk. However when I attached my nrf5340 dk and hit debug in the nrf connect extension, the process stops...
I am working on the http server. I wanted to make my device behave as a server so that I can send the data (received through uart) as a response to the client.
The problem...
Hi,
I am developing a nrf5340 based device (no external memory) using FOTA to update the firmware. This process used to work quite well for a while now, but I ran into trouble...
Hi ,I am new to nrf .I am currently using nrf5340,so i want to just print raw data of sph0645 using zephyr.I tested with examples of echo but i didnt achieved to print raw...
Dear all,
I'm designing a circuit that should allow powering the nRF52840 board with either an USB power supply (USB2) or a (non-rechargeable) CR2032 battery (B1). According...
Hello.
I encountered the following problem. I have an nRF52840 microcontroller that is already soldered onto the PCB board. It doesn't have any bootloader. As an example...
Hi,
We have an nRF9161DK and received our own custom boards this week. When we tried to program our custom board, the development kit disconnected from the computer and...
Hi all!
I'm in the process of trying to put together an nb-iot app on Android studios that would communicate with data from the Thingy 91 board. I've been trying to go through...
Above is the trace and the commands inserted. We were unable to get a response using the at+cops? command. Both SIM cards were active that we tested. We tested band 12. Could...
Hello everyone,
I've been working on testing PPP support in SLM 2.6.1 without cmux on my Linux host machine. However, I encountered some logs during the process: Note: For...
Hi
I have 2 BLE boards with some environment sensors on them.
I need to synchronise the 2 boards with < 1 mili second precision.
one board is configured as central,...
Environment:
I can't seem to get the one button sample to do anything... I get a steady ~1sec flash from HOST led on the npm1300, but I get nothing from pushing SHPHLD...
Hi.
I have following error:
Here is my prj.conf :
I would like to avoid using CONFIG_SHARED_INTERRUPTS.
Only GPIOTE0 is on IRQ number 11 so I couldn...
Hi
I'm having an issue with my NPM1300. drawing high current. I've had 50 of these boards fabricated and the majority are fine, but with the same hw configuration, same...