GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi all
I have a problem with allocate RAM.
I build the project as non secure.
in the zephyr.dts file, you can see that the memory is divided into 3 areas:
sram0_s...
Hi
I have nrf52833DK it was working all fine but suddenly the LED5 is not lighting up and it is not detected by USB port. I tried to check the board voltage regulators and...
Hello,
I just started working on the nRF52 series controller, I want to upgrade my project using BLE features.
I need 1 master device to send to multiple slave devices...
Hi,
According to CryptoCell-312 documentation , it supports the SHA-1 algorithm. I was able to successfully run the SHA-256 cryptography sample application in the nRF Connect...
In my application, I need to use the nrf52840 for both BLE (as the controller) and ShockBurst. Specifically, it's the nrf52840 on the nrf9160 if it matters. I'm using the...
Hi Team,
We are working on nRF52840 SOC with BLE functionalities.
We need the mechanism for to find out the BLE or BLE Stack is in Hanging state before the processor is...
Hi,
I'm trying to build a proof of concept for a BLE gateway that captures data from BLE sensors and sends it to the cloud via LTE-M connection. I'm hoping that the gateway...
problem description:
hi, I just got a PCA10040 development board with which I plan to learn about nrf connect SDK.
so I try the common BLE peripheral demo,but I 've met...
In order to add the BLE DFU service, I need to increase the GATT table size and therefore memory as mentioned here: .
However, when I tried to increase the file ble_app_uart_gcc_nrf52...
Try by changing the RAM size but it didn't worked.
<info> app_timer: RTC: initialized. <error> app: ERROR 4 [NRF_ERROR_NO_MEM] at :0 PC at: 0x00000000 <error> app: End of...
Hello, I have managed to get two NRF5340DK linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to test again. And then I also need...
Hello Nordic Team,
I have an issue on one of my 10056 DK. The DK is connected to a development PC, appears in device manager as a Jlink CDC UART port, and as a mass storage...
In the Zigbee framework, what is the purpose of the return variable from zb_osif_sleep() ? The "documentation" for Zigbee seems to implement a "guess and figure it out for...
Hi,
I'm following the ble_template example on my custom board. I'm having an issue with waking up (soft reset) the device from sd_power_system_off. I can power off the system...
Hi ,
We are using s140_nrf52_6.0.0_softdevice, SDK 15.0.0 for NRF52840 chip. Does this sdk and soft device supports extended advertisement?
I could able to enable this...
