hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I want to creat a hci vendor-specific command of zephyr using nRF connect SDK, based on hci_pwr_ctrl bluetooth sample.
At first, I think just using follow steps in hci_vs...
Hi,
Recently I have heard that there are license restrictions on using DKs for production programming. Is this only for production programming? Can I still use the DK to...
Hello, im trying to implement the UARTE Driver for simultaneous Use of Bluetooth and asynchrounos Uart TX/RX on a nRF52840 and nrf9160. The Problem is that neither RX or TX...
Hi
i want use a nRF52840Dongle as a Zigbee end device, when power up, i get following message:
I: nRF5 802154 radio initialized ***** delaying boot 5000ms (per build configuration...
Hi, I have just started evaluating nRF52840 using the dongle and Development Kit. I have successfully tested the Openthread network using CLI project. Now I want to try out...
Hi experts, The situation is following, the NRF53 shall receive multiple packets. After the reception of one of the packets the next one shall be received at the same frequency...
Hello,
I am struggling to commission a light bulb matter sample device (nrf52840dk) with the CHIP tool running on my Linux laptop. I set up an OpenThread Border Router with...
I had configured zephyr.dts file for UART and I2C pheripherals. And when I tried to build an application it is giving below error
Board : nrf5340 Application name : SHT...
I implemented the nRF52840 (auto)upgrade with an nRF9160 on the nRF9160DK. I did my development with the Serial Modem LTE application from nRF Connect SDK 2.0.0. I noticed...
Hey All:
I'm trying to install V2.0.0 of the NRF Connect SDK on a fresh Ubuntu 22.04 VM, and the whole thing seems broken.
Here's my steps:
install the nRF command...
Hi, I have found several aged topics on Devzone but need this feature and would like current state. If it still not supported, is there any example implementation on how manage...
Is there a way to rebuild (clean and build) a project in Visual Studio Code with the nRF Connect Extension? A web search shows how to do it with the CMake Extension ( https...
I am using the Connect SDK v2.0.0 and attempting to use TCP in the stock CLI example to mimic the demo shown here . When I flash the v2.0.0 CLI sample on my nRF52840dk, "...
Hi everyone,
I have some devices that are communicated through RS485. nRF52840 DK supports RS485 communication?
Do you have suggestions of how should I connect those devices...
I have a custom board with 8 LED's and I use pwm API led_on(), led_off, led_blink() etc, to turn them on, set brightness and blink and everything works fine except one case...
