Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I read this post https://devzone.nordicsemi.com/f/nordic-q-a/10668/rssi-without-connection
I want to know how large the RSSI value will affect the connection. Is there a...
Hi,
I am developing firmware for NRF52811, using SDK 17.1.0 and Soft Device S112.
I need to write a characteristic longer than 20 bytes. I thought it could be done with...
The bluetooth connection is automatically disconnected, and the reason is 0x3E. Is this related to the small RSSI value? I set the transmitting power as 4DB, and the RSSI...
Hello,
I'm exploring the nrf5340 controller with a Fanstel evaluation board (EV-BT40) I use the SDK V1.7.1 with vsCode.
Used example "Bluetooth: Peripheral LBS".
Connecting...
I've recently flashed USB CDC ACM example to NRF52833. Even though everything seems to be working, there is no COM port listed on Windows. I've also tried Zephyr's USB CDC...
I got 2 NRF52840-DK Development Kit recently. But for one of the boards, the programmer firmeware encountered timeout during upgrade. The other board did not encounter this...
Hello All,
I am using nRF52840 Dev-kit and SDK 4.0 for Zigbee and thread. Due to some functions, we are using SDK 4.0 for this project which is not present in SDK 4.1. ...
Hello
In my another ticket https://devzone.nordicsemi.com/f/nordic-q-a/81555/ncs-upgradable-bootloader .
I know there is currently no support for upgrading the bootloader...
Hello,
I build my project with “Visual Studio Code” and with “SEGGER Embedded Studio”. There are some warnings when I use VS Code. When I use SEGGER to build the code...
Hi,
Im using nrf9160 based custom board, nrf sdk 1.5.1
I have below structure to frame the data packet and i need to send this packet to another thread through MailBox...
Hello.
I am developing with nRF52840DK.
Normally, I think that the buck regulator supplys 3.0V to Interface MCU and nRF52840.
I want to connect the 1.8V peripheral...
We're working on an nRF52840-based project that started development on SDK 17.0.0 and Softdevice S140 7.0.1, but we wanted to get it to the latest release before production...
Hello,
I am working on Arduino's platform and decided to ditch the ArduinoBLE.h library due to its overhead.
I would like to send high frequency (2Mbps per the spec ,...
Hi,
I've trying to get the Omnivision OV7670 to work with the nRF52840-DK. I'm not completely sure whether I've configured it correctly. My pin assignments are adapted from...
