Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
SDK: 15.3.0 Example: ble_app_multirole_lesc DeviceA: EYSHJNZWZ (nRF52832)
I want to know the relationship between API and events. Take "sd_ble_gattc_characteristics_discover...
Hi nRF Support,
I get nRF5 SDK version 17.0.2 and learn Peer Manager handler implementation (pm_handler_flash_clean function). Lets consider this case:
- 2 bonded peers...
My thingy:91 does not connect to the LTE network. However it does detect the Swisscom network (Switzerland) and shows it as available.
I did:
update the modem with mfwnrf9160123...
Hello, I am trying to program the peripheral uart sample on to my Thingy 91 using the nRF9160dk and 10 pin connector. I am able to successfully build and download the target...
I hope I am posting this in the right place but I am looking into learning more about developing devices that use Bluetooth. I have been looking into getting a dev board but...
Hello All,
I am working on nRF52840 DV-kit, using SDK - nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71
I am trying to create .c and .h file in my project for gpio_configuration...
Hi,
I have layout a borad with nRF52810 and use IO to control other ICs.IOs map as blow.
#define LSM_6DS_SPI_CLK_PIN 9 /**< SPI */ #define LSM_6DS_SPI_CS_PIN 4 #define...
We are using nRF52840 chip for our development and till now we have used nRF SDK's zigbee CLI example for development.
Now we are interested in nRF5340 chip but I have not...
hi，
iI'm newer useing nRF5340， nRF5340 two cores communicate via IPC ,then exchange data through which path that is IPC or CTM ，What's the difference between IPC and CTM...
Hi,
I am powering the NRF52840 in normal mode by supplying 1.8v to VDD with VDDH and VDD shorted.
In order to use USB the VBUS pin is connected to the USB VBUS line. ...
Hi,
I am programming the PCA10040 board (tested 2 different boards) with the ram retention example program from the latest SDK (NR5 17.0.2). With this example is supposed...
Hi :
We create UART Over BLE service on NRF52832 SoC. It worked fine used SoftDevice V2.0.
Now update SoftDevice to V7.2.0. got this issue. where can i found SoftDevice...
I'm trying to drive the RGB LED light on the Thingy:91. So far, I've not been successful. I was hoping that by listing the steps I perform I might be able to get some advice...
Hi,rotocol
In Nordic's Smart Remote 3, it is mentioned that IR transmitter is protocol agnostics while IR driver is Protocol specific. Is it possible to write a common IR...
Hi,
Is there any battery life calculations for NRF52 and NRF51 (Beacon)?
For example: if TX power of NRF52 is 0 dBm and it broadcast every 5 seconds ? Or with any other...
