Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
I'm testing the Zigbee CLI Agent example and try to read info from my Titan wall sensor. I can read almost all info, but not values, that are using float type.
How I can...
Hi everyone,
I have an issue when i am writing to flash sometimes i get a SOFTDEVICE assertion failed just after using the function fds_gc().
The structure i write...
Hi,
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/45544/nrf9160-dk-psm-current-too-high-after-opening-and-closing-a-tcp-socket/260026#260026 , however they said...
I have been looking at the Mesh library for BLE communication and wonder how much work it would be for me to use the same library for a long range 2,4 GHz radio?
Is the...
Hi,
now we use SDK17 "ble_app_hids_keyboard" example, we found after the moble phone connected to the ble keyboard, if the ble keyboard power off and power on ,the phone...
I am trying to to do adc reading from external 9V Litum battery.
In the PS document, I know nRF52832 can read adc until VDD(3.7V ???).
Then, in my case, do I have to design...
Hi,
I use the timestamp log in SDK17, and I find the time will auto clean at about 1min6-7sec.
Below is the code init the log.
/**********************************...
Hello,
I have a setup containing an NRF9160 communicating with another chip over UART at a 1M baudrate.
The following code is currently used:
I have configured the...
Hello team,
Greetings From Deepa. I need an manual installation procedure and building, compiling and Running the zephyr -OS with my laptop for learning purpose. I browsed...
I'm using nRF52840, PCA10056, and finding that if WDT is enabled (but not expired), after a soft reset (NVIC_SystemReset, or a debugger reset) the RTC no longer runs.
If...
Hi,
#define TIMEOUT_INTERVAL 2000 // Two second.
Sometimes starting app_timer_start(motTimeout_trigger_time_id, APP_TIMER_TICKS(TIMEOUT_INTERVAL), NULL), the interrupt...
Hi,
I'm wondering if I'm doing correct by following getting started guide of nRF9160 ( https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular...
Hello,
We start a new development in BLE and for this, we have to use the AVRCP profile.
Is this profile available with the Nordic BLE stack (SoftDevice)?
Thank you...
Hi,
my question might sound a bit silly, but I am certain that someone already faced the problem therefore I am wondering how it was addressed.
The question:
what is...
