Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi, I am looking where can I get the ACK from the light bulb, in Zigbee light control example. I am using the latest sdk nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
what...
Hi,
The documentation for the simple_on_off model in the nRF5 SDK for MESH v4.1.0 states that the light_switch example uses the simple_on_off model.
The documentation...
I think spi slave pins should set as input but I want to control CSN pin as output in spi slave mode on nrf52840. Is it possible it?
I know that CSN pin is controlled by...
Thingy91 is useless without working samples and SDK
Out of the box it cannot associate with any NB-IoT cells here in Bulgaria. I tied using the provided SIM card from iBasis...
Hi I am having some trouble changing BLE connection parameters (mainly due to the connection handle). Is there any working example that I can refer to, which explains how...
Hi Nordic folks,
Our project is using nrf52840-DK boards as the development beds. We're developing a security application by leveraging the internal CryptoCell CC310 inside...
Hi everyone,
I successfully tested the example of the MQTT publisher in the IOT sdk on a NRF52840 and a raspberry pi 3+. The messages end up in my mosquitto install and...
Hi,
We have seen random ARM faults.
After some time we have seen that the lr register often pointed to entropy_cc310_rng_get_entropy.
This is our setup:
- Environment...
I recently purchased nRF52840 DK. While scanning through the website, I came across a suggestion to start with Blinky example. I opened the project in Segger Embedded studio...
Hi,
Observed that Openthread CLI project in NCS v1.3.0 is not compiling as it is using Segger Studio but building with command line. Please fix this.
Thanks
Sridh...
Hi Nordic experts,
I am trying to use Segger IDE to build the mcuboot boot-loader for NRF52x development kit. I am using NRF connect SDK 1.3.0 While I can build it successfully...
Hi
I am facing two issues in the below code. I use segger embedded studio.
1.The value I am setting as fs_initialized = true in line number 90 (inside FRESULT fs_init...
Hello,
I'm working with nRF5 SDK v16.0.0.
The documentation on Hardfault handler implementation clearly suggests to define DEBUG_NRF in order to get an automatic breakpoint...
I have the Thingy91 module, everything is working when I (turn off modem then) set AT%XSYSTEMMODE=1,0,0,0 (and turn on modem again), but if I power cycle the device the original...
