hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
So I recently purchased an nrf52840 pdk and was following nordics getting started guide. however my pc will not detect my board when i plug it into the usb. When i plug the...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello,
I'd like to use a central_peripheral example project (sdk 15.3) : Experimental: ATT_MTU Throughput Example
What does it mean that an example project is experimental...
Hello,
I have a problem with using the FDS library.
I started by exploring the example CLI program (examples\peripheral\flash_fds), it seemed to work as expected.
Then...
Hi
I have a nRF52832-DK based central node and multiple nrf52832 based peripheral nodes implemented using a combination of ble app uart c + multilink central at the central...
Hi Guys,
I am trying to access the serial number written on MCU through software.
White strip on MCU has details such as PCA10056, 1.0.0, 2018.04, 683xxxxxx. I am trying...
The Qorvo QM14501 LNA in nRF9160 reference schematic seems to be consuming several mA of current, which is quite a lot for a GPS LNA. There are other LNA chips in the market...
Hi
When I use the nRF5_SDK_14.2.0 of nRF52832, the example is selected ble_app_uart. And the Android example is the Android_UART_Client_Bluethoot_Sensor_Nordic_CortexM4_NRF52832...
Dear team, Device - nRF52832 SDK - SDK_15.0.0 IDE - Segger Embedded studio Softdevice - s132_nrf52_6.0.0 I am doing buttonless DFU in my application. I have successfully build...
Hi,
I want to use uart. I configured two uart, uart0 and uart1. I want to read and write to one uart using APP_UART_PUT and APP_UART_GET. how it possible without uart event...
I am trying to modify tx settings in open thread but when I try to execute otLinkSetMaxTransmitPower it cannot find this function. It seems to find all others. Is this not...
Hello,
I'm using a nrf51422_xxac_s110 chip, with the 12.3 SDK. My code is based on the ble_peripheral\ble_app_uart example in the 12.3 SDK. I'm hoping you can provide some...
Hi,
We believe we have either a BT communication issue for Nordic Semiconductor ASA NRF52832-QFAB-R
https://www.digikey.com/products/en?keywords=1490-1055-1-ND
...
