I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi All
I know this is stupid but I can't figure it out - either I've missed something obvious or not connected something properly (or at all).
Using the PCA10040 nRF5...
I have developed a custom board with NRF52810 (Rigado), a standalone CAN controller (500 kbaud) and serial communication (57600 baud).
The SW is based on the BLE_APP_UART...
Can anyone tell all the potential reasons for stack corruption? I'm debuging a problem where sometimes there is no stack trace when putting a breakpoint on the first line...
I have a project based on SDK 15.3
I've set #define NRF_LOG_DEFERRED 1
The project generates a high volume of log output over RTT
NRF_LOG_FLOAT_MARKER is a macro that...
Hi, I am using the nRF51822 with SDK 12.3.0
I am trying to make use of nrf_drv_spis driver included in the SDK.
My purpose is to have nRF51822 constantly be RX-ing over...
While investigating my stack corruption issue , I noticed that the RADIO_IRQHandler is always called twice in quick succession:
But the NRF_RADIO->INTENSET register only...
I'm trying to communicate between two devices (nrf52840 and teensy 3.6) over RS485, but I'm having some issues using the UART library in the SDK. I'm trying to create an interrupt...
Hi,
It all happened today after being used the board for a month. when I tried to turn on the board it does not blink LED5 nor does it show up in the device manager. I to...
Hello Nordic,
I have multiple Thingy52 devices upgraded to V2.2 firmware via nRF Connect application on my android phone.
Have been trying to add the BL Mesh light switch...
I want to read timestamp in my nRF9160 device and found that "z_tsc_read()" function in Zephyr RTOS will do that. However, I am not able to include the main library of the...
Hi,
We are developing mesh control lighting system with nrf52832, now we're able to control devices through mesh.
But now we're having problem with showing node state...
Hello,
I have two devices, one central and one peripheral and I try to implement whitelist. I took a look at ble_app_hrs_c example and the whiltelist is working on central...
Hello,
I am using ble_app_blinky. I have a basic query about event handles. There are lot of event handlers registers as part of initialization. Will all these event handlers...
Hi all, we has experienced two PPK boards start to give faulty reading after several uses. I attached two screenshots about current reading with same setting on the DEV board...
Hi,
after having a little break from ot and working on another project, I am back working on getting the NRF into systemOFF. to get back into it I just made a very small...
