hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I wrote my program on PCA10056, N52840, with fds_init() it everything was working fine. Now using the same main.c file I wanted to program a N52832 which comes to PCA10040...
I am very new to Nordic products so please excuse my ignorance.I have been trying to put my nrf52840 board to deep sleep. It seems to go to sleep but when I try to wake it...
Hi,
I'm porting code from Simblee/Arduino to Laird's BL651/Nordic SDK (nRF52810, SDK 15.3, S112). (Simblee discontinued.) For accurate timing of a GPIO pin, I use TIMER1...
Is anyone else having issues with the Zephyr shell on the NRF9160 DK? We weren't able to get it working on our code, so we went back to the coap_client applications in the...
Hello,
I was working with Asset Tracker sample and tried to add LTE device in Cambridge, UK. It worked, both LED 3 and 4 were blinking and added device to the nRF Cloud...
In advance I would like to say I’m sorry for the frustration that this message reflects…Event though I have been using the UART for some time, adding more functionality makes...
On nRF52832,
A1> Out of the Softdevice scope: if we are using RTC and have LFCLKSRC configured to XTAL source and if XTAL source gets turned off for some reason what happens...
Hi,
I am struggling with a low power consumption solution for waking the NRF52832 with our product which is using a third part module.
Currently our product total power...
Hi, I have Lenovo tab E8 tablet with Android 7.0 and I connect to a BLE device (nrf52832 SDK 15.2.0 S132) from my Qt 5.11.2 app. After succesfull connection I discover services...
The toolchain setup of the NRF91 is extremely complicated. Is the a VM Image or Docker container that has everything pre-configured? I am trying to setup up a linux VM now...
I have a 52840-DK (PCA10056) connected over USB on Windows 10. I am using IAR and can build and run demos from EW in this configuration but am having no success with nrfConnect...
I am working on a project on the nrf52832 board using mesh SDK v3.2.0 and SDK v15.3. I am trying to troubleshoot an issue with the publish process for BLE mesh, but I am not...
Testing DFU with IOS version of nRF connect. I am able to save my image to the IPad with Itunes. I can select the file and then start the DFU process.
Process completes...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Dear Support,
In our new project, we have 8 signal LED diodes attached to nrf52832, they are all sinking current:
3x GREEN 0.8mA (P0.16, P0.17, P0.18)
1x RED 3.3mA...
