Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello,
we plan to develop an BLE-application that needs to be as low cost as possible. One of my favourite BLE-SoCs in regard of pricing is the nRF51822-QFAB with 128kB...
Hi, I'm looking for a way to communicate with Blue tooth. I need a low footprint chip that allows for a BT HID gamepad application. I'd prefer to communicate via i2c, or some...
My application uses the nRF51822 with a GPIO configured as output and another GPIO is configured as input. Connected to the GPIO_OUT is a resistive load (Rload) which then...
Hi, we switched from your competition to your platform. I know you wrote somewhere that you cannot provide examples for every sensor out there. But your Nordic Dev Zone is...
I have run many tests using the light_switch demo. I have noticed that occasionally the latency is much larger. The latency jump is between sends, i.e. it will send 20 times...
I am using 3 mobiles for testing
1. One Plus 6
2. Samsung Galaxy Note 8 or Google Pixel
When I connect my hardware with #1 phone and send some data from the nRF Connect...
hello.
i am new to nrf52832
my question is when i press the button it will goes to interrupt handler then turn on the led if i press the same button led will turn off...
LTE link monitor does not work.
OS: Mac SEGGER IDE: v4.16 place: Tokyo in Japan.
I set up the environment from scratch following Get Started Assistant v0.9.2, updated...
Hi,
our installed base of sensors transmit their data in periodic BLE 4.0 beacons. I would like to develop a relay board that receives these beacons, and then retransmits...
Hi,
I want to use the nRF9160 DK for an NB-IoT application. I am located in Bavaria, Germany where there is no LTE-M coverage. I understand that I need the NB-IoT version...
To the kind attention of Nordic support team, from www.nordicsemi.com/ I downloaded all nRF24 Files.
I found very interesting the nRFgo Motherboard (nRF6310 Rev 1.4) pinout...
Hello ,
I am new to nrf52832
i am using external interrupt for led on and off
here the problem is when i press the button 1 led will turned on if i press the same button...
For Zigbee RF manufacture test, we did try nRF52840 using the sample code "radio_test" in SDK nRF5_SDK_15.3.0_59ac345,
but it seems that only the TX power information can...
Hi all,
I'm developing a buttonless DFU based application using the SDK v15.3 Following the documentation was pretty easy and I'm now able to run the app_ble_buttonless_dfu...
Hello All,
I am working on nRF51822. Use nRF51 SDk 12.3.0 version for reference. Writing program in IAR in windows.
Porting the OTA DFU to my custom APP.
use SDK 12...
