Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I have a BLE project that I wish to add Zigbee to (non-concurrent, if that matters). The project is built on FreeRTOS with several threads, using SDK 5.2.0 and S140 6.1.1...
Hi,
I am using nRF52840-DK evaluation for testing a Mesh configuration. I was able to successfully establish a mesh connection with a onoff-sample from zephyr and was able...
I am working on the project with radio transmitter(NRF24L01+) and receiver(NRF52840). I need to receive data at the rate of 250kbs. I tried to receive but it fails always...
Hello,
I want to interface a microcontroller with the nRF52832 chip in one of our designs. The microcontroller will be running on FreeRTOS.
I would like to know a few...
Hi,
We are currently in a testing phase of our software where we use an nRF52832 for extended advertising and an nRF52840 for scanning that has a scan interval and scan...
Hello, i´m trying make DFU with the Light switch server with the GATT and Proxy Enable, however in the process of update, i got this error in the device what receive the update...
Trying to lower uC current consumption to minimum
Im trying to remove features from my program
I've notice that removing the adc initialization actually get the current...
Hi All
I mount a minimum system for test BLE. I download a blinky program to the NRF52810. If I download a blinky without BLE version , it works well . But if I download...
Hi dear Nordic engineers and enthusiasts,
I am currently testing and researching on the functionalities of Nordic Thingy 52 in Bluetooth Mesh . I have tested with the provided...
Hi
I am trying to use the TWI on nrf52840 but i am unable to get it to work. its getting stuck somewhere. I dont have a logic analyzer so i am unable to check if the signal...
Hi,
I'm doing some experimental evaluation of BLE Long Range. I use the ble_app_att_mtu_throughput example with parameters:
ATT MTU: 247 bytes
Data length extension...
I am trying to test out the whitelist that I have created for the nrf52832 client. I have edited the whitelist so it will only allow one device to be bonded and added to the...
Hello, We have choose NRF52840-QIAA-R for our design, can you give me more infrmation on microvia use between layer 1 and layer 2 please?
What is drilling and pad dimension...
hello,
When looking at the 3 different migrations scenarios at
https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/nrfx_migration_user_guide#getting_started_replace_nrf_drv_options_migrate...
