I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
Hello,
Greetings, in the nRF24L01 datasheet, its mentioned that the module can work as a multiceiver, meaning 5 nRF24L01 module acting as PTx can communicate with 1 nRF24L01...
hi,
my customer using nrf51822 DK to have debugging software,the error occur in the attachment.
can you tell me something have Caused this problem?
thank you !...
I am using the code
err_code = sd_ble_gap_device_name_set(&sec_mode, (const uint8_t *)deviceName, nameLen);
I have made sure that nameLen is less than BLE_GAP_DEVNAME_MAX_LEN...
Hi
i am using twi_hw_master.c for i2c communication of accelerometer.
my accelerometer address is 0x18.
once i call
twi_master_transfer(0x18,dataW,1,1);
in...
Hi,
Can the value of NRF_RTC1->COUNTER be read safely from the main loop without first stopping the RTC or temporarily disabling the RTC1 interrupt etc? (nRF51822 or nRF51922...
I used the nRF51822 Evaluation kit and flashed the BLE_proximity example on to the PCA100001 board.
In the master control panel the USB dongle measured -46 dBm(Nordic_prox...
Hi all,
what if I want a sensor network in my house with BLE. Can I just install, for example, 16 nodes in my house and connect to all of them with one iPhone? Or would...
Hello,
I am currently using nRF24L01P with TI CC2591 in my RF module product.
I have a doubt that need your help to clarify.
Does the antenna impedance given in the...
We've been trying to user the AES hardware module in ECB mode.
To do that we used the sd_ecb_block_encrypt function.
Is this hardware accelerated? Based on power consumption...
Hello,
I would like to know if I could interface the nRF51822 with an Arduino Mega Board. Could you give me some advices to do that?
Thanks for your help
Hi,
i need to use a watchdog in my application. I read that i can use the build in one, but i thing my configuration or the usage of the watchdog is wrong.
here is my config...
Hi guys,
I am getting started with your nRF51822 dev Kit. I got the nRFGo Starter Kit (nRF6310 Rev 1.4 mother board) as well. Most of the examples work as expected. But...
