SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Dear Nordic Semiconductor Support Team,
Thank you for providing the nRF54L15-QFAA reference design files.
I have downloaded the schematic and PCB design files, which...
During reset and initialization are the NFC pins configured as GPIO or as NFC?
If they are in NFC mode can you clarify if they have any special behavior on boot (pulls,...
nrf52840, Zephyr, ncs 3.4.1
For a few months I have been tracking an intermittent issue with a product that is close to production release.
The symptom of this problem...
I'm working on an open source smart watch project https://github.com/Protocentral/healthypi-move-fw . I'm after serial communication with another device, so I need to re-enable...
Hello Nordic Support,
We are evaluating nRF52840 and nRF54L15 for a battery-powered rotary Zigbee remote. It must commission several commercial Touchlink dimmers without...
Hi,
just got my PPK2 and noticed some strange behavior:
the only thing connected is USB data/power, no DUT. Power output is off. If you start logging it displays some...
I have already make spi-bitbang work on ncs v3.0.0 on nrf54l15 custom board, but after migrating into ncs v3.4.1(latest release version), spi-bitbang not work same with older...
I am seeing a reproducible interaction between asynchronous UART support and the TWIS peripheral on an nRF52840 running NCS v3.4.0.
The application uses nrfx TWIS to implement...
I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
Hi,
Does Nordic offer, or have plans to add, a FIPS 140-3 validated cryptographic module directly in the nRF Connect SDK for the nRF54L15?
We are evaluating the wolfSSL...
Dear Support Team, We have developed a product based on the nRF5340, using the Insight SIP ISP2053 module. So far, we have built approximately 25 prototype units and around...
The nRF91 series of modem firmware are distributed with FOTA-TEST diffs to allow for validation of FOTA integrations. Will the nRF93M1 firmware images be distributed with...
Hello,
we have a custom PCB with the NRF54LM20B (nRF54LM20B_xxAA_ENGB) and nPM1300, and we are observing odd behavior with the LFXO failing to start from a cold boot, causing...
Hi I have a NRF52833 module in my PCB design. Are there any end of line tests you would recommend at the end of my production line?(end of line tests) I am using a Panasonic...
