Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello Nordic Team!
I updated to version 5.0.0 of NRF Connect for Desktop and since then, when I try to program my development kit in VS Code, it can appear as connected...
Hello,
I wanted to evaluate the nRF53 platform with nrf connect SDK so I got new nRF7002DK board. I have following versions of all tools installed.
- nRF connect SDK ...
I want to edit the sample source (nRF5340 Audio) and program it on my own board. The connection is CIS. I am using NCS version 2.5.0.
I want to set the I2S clock as follows...
I tried the following settings to output 12.288MHz I2S MCLK with nRF5340 Audio, but it did not work as expected.
The I2S settings I want to output are as follows.
MCLK...
I am currently writing sniffer firmware to the nRF52840 and am trying to check Thread communication using WireShark.
When I displayed the RSS, I got the value shown in the...
Hi,
I am just starting to develop a nRF5340 based prototype. I am using the openthread CLI example as the first step. I have configured the device tree to suit our board...
Hello. We recently started working with the new nrf connect sdk and we need to implement a very simple bootloader that would only jump to the main application at a specific...
Hi there,
I have a project developed in SES, using nRF5 SDK v15.3.0 with only Just Works security without using LESC running on nRF52840. It has been running fine for 2...
In our custom board we checked WIFI, facing below issues, 1. We flashed sta sample project to our custom board facing the issue below. Is there any configuration needed to...
I am using Asynchronous API of uart to receive the data. During the reception I face UART_ERROR_FRAMING issue in UART_RX_STOP event. But after getting that too it enables...
I use the nRF52840 development kit. In this Board i flashed the ncs zephyr sdk v2.6.0 sample code for system off and device going to sleep.
i Want to wakeup the board from...
I made an assumption that the nRF52840 Dongle has the ability to communicate via UART as most boards I worked with have this feature. This seems not to be true, but I don...
Hi
1. How to set PWM power-on state to Low level in ncs v2.4.1 2. How to configure the dts file so that the corresponding I/O port is in the low state when PWM is powered...
Can we run our Customised Bluetooth Host Stack on nRF5340.
Please provide us with sample Brinup Code for Bluetooth Controller.. Send HCI Reset and Bringing up the Controller...
