[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I am working with the nRF54L15 to create a driver for a peripheral which is controlled by two PWM signals.
My driver relies on the Zephyr PWM driver which goes back to your...
HI
How much current dose the individual GPIO pin source/sink for nRF5340 as in the datasheet V1.3 it is mentioned "Added guidance on maximum combined GPIO sink/source current...
Hello,
we want to setup an environment for automated testing of our bluetooth mesh system.
The test system should be able to provision and communicate over a device that...
Hi
If my calculations are correct the NORDIC whitepaper WP008 on PRINTED MONOPOLE ANTENNA for 2.45Ghz the quarter wave length antenna trace is not 92mm
For TOP layer PCB...
Hi,
I was trying to get the NFC Sample programs to work on the nRF52840 DK but the NFC tag is not being read by my phone. The program itself is running (confimed through...
I am working on a school project and need to set up SPI communication between a wiznet,W5500 and the nRF54L15DK. I can build and run my program but I am getting no responce...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hello,
With NCS v 3.2.1, I am working on a BLE application with nRF52840 dongle.
I was trying to add FOTA feature in my application by adding the following line to sysbuild...
I just ordered and opened up the nRF9160 dev kit from Digikey. I was going through the quick start and I named the device and when I went through the verification step, it...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
We have a Thingy:91 (nRF9160) that we use for various LTE-M / NB-IoT network debugging. Until recently I was able to see both RRC and NAS messages in both " Cellular Monitor...
Hello,
I am developping an application based on ESB protocole using BT840NE module (nrf52840 + nRF21540) SDK 3.2.0.
on the PTX side, I am measuring the current using the...
Hello,
I am a developer/maintainer for the RF24 Arduino library at https://github.com/nRF24/RF24
I've found in some cases, the R_RX_PL_WID register returns 0 while the...
When updating from nRF connect SDK v3.0.1 to v3.1.0 we noticed a change in the clock_gettime() function.
In the old version, the clock was not reset by a reboot.
The new...
nRF5340 I2S MCLK issue – unable to get 12.288 MHz MCLK for 48 kHz sampling
I am using the nRF5340 SoC and configuring the I2S peripheral as Master to achieve a 48 kHz audio...
