[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I want to use the BLE Secure connection feature with the following options
CONFIG_BT_SMP_SC_PAIR_ONLY=y
CONFIG_BT_SMP_SC_ONLY=y
CONFIG_BT_SMP_APP_PAIRING_ACCEPT=y
CONFIG_BT_SMP_DISABLE_LEGACY_JW_PASSKEY...
Hi
I'm working with a PDM mic for nRF52832 SDK v17.1 on a project and I have a questions about PDM driver working.
Whats the difference between the buffer pointer in nrfx_pdm_buffer_set...
Hi Team
In thingy91---hardware-files-1_6_0.zip, the QM12038 is end of life status now. So do we have any new design to replaced it? Thank you.
www.qorvo.com/.../QM12038...
I just finished the second prototype of a nRF9160 board. First one worked flawlessly, but had poor GPS reception. Rewamped the matching and added SAW filters.
However, now...
I have to switch between several different scanning modes.
I scan in passive mode to get all sensors' advertisements (no connection).
I scan in active mode to get a specific...
Hi everyone
I want use the pwm_driver example of the SDK download at nRF52833 DK
However, some problems were encountered after the migration
I replace the preprocessor...
Hi,
I just started looking around with the NRF52840 development kit and tried to implement simple GPIO interrupt based on the button sample .
I settled multiple GPIO...
Hi All,
If I enable UART module or my code has any stdio functions retargeting to read/write, the debug mode does not work. I am getting the following error:
========...
Hi,
I develop firmware for nRF5340 in VS Code with Nordic toolchain (1.9.1) and NRF connect addon.
Project generates multiple elf files and it seems like only zephyr\zephyr...
Greetings to Nordic team!
I would like to provide BLE security for my application (to my BLE Peripheral device). I am planning to apply the following features such as...
Hi Nodic community,
Could you please help me to flash my Nordic Thingy:91 development board. I was able successfully build Zephyr-based project by following instructions...
I have been trying to achieve a delay of 1 Us , I have tried using Kernel timers and even tried fetching the system clock and getting the difference, But I am unable to figure...
The Online Power Profiler ( ) shows a reduction in power usage for the central with non-zero Slave Latency figures. Why is this? I thought Slave latency only reduced power...
Hi:
when i set the timeslot parameter see below:I found it will run.H owever, after running for a few seconds, the program hangs. Debugging found that the softdevice hangs...
We are evaluating a number of Thingy:91 to track GNSS positions and reporting them to nRF Cloud using the Asset Tracker V2 firmware. When running the Asset Tracker in Active...
