Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone,
at the moment I am working on a BLE program which collects data from various sensors and passes it to a Central device. For the transmission the BLE NUS...
I am using ESB with dynamic payload lengths. When I use length 252, I am sending the alphabet repeating, and I can see that the data cuts off around position 30 and repeats...
Are there any known issues when using a nRF52840 and S140 6.0.0 soft device and trying to transmit at +8 dB? From our measurements is appears that +4dB does indeed increase...
Hello,
I am using the nRF 9160 DK board. I am trying to create simple thread in Zephyr.
but the thread it's not running.
this is the code:
I tried also the other...
I accidentally pressed "verified" on https://devzone.nordicsemi.com/f/nordic-q-a/91104/making-rand-work-on-nrf52-nrf53-with-nrf-connect-sdk when it wasn't and I don't seem...
I am testing my own mesh protocol based on 802.15.4 using the NRF52840 dongle.
The reported RSSI value from nrf_radio_rssi_sample_get() never goes below -89dbm.
On the...
Hi,
I'm using a nrf52832 and NCS 1.9.0 and I would like to be able to use SMP to make firmware updates using BLE. I'm was able to perform FOTA, but the flash is divided...
Greetings!
We are trying to troubleshoot occasional hangup issue. We run the app in debug mode. When it hangs up, we hit pause and got the followings in the Call Stack window...
Hi,
I want to use nrf5340 dk board to debug nrf52840dongle, i have connected two board with a cable and have checked the signal is good( nrf5340 debug out p19 ------ nrf52840...
Hello all
the BLE module with the nRF52820 is programmed with a ble_app_uart_pca100e example from the nRF5SDK ver 17.1.0, according to the RSSI graph it seems it works ...
Hello Reader, I noticed two almost similar modules " DK buttons and LEDs" library and the "CAF LED & Button" library (or module). What is the difference between DK buttons...
I get the following error message from my device
àÓ FATAL: Exception occurred in Secure State [10.2 10:01:52.062]FATAL: ***** HARD FAULT ***** [10.2 10:01:52.062]FATAL:...
We have both native iOS and Android-apps that handle DFU-updates of our BLE-FW on our HW-devices. We are currently experiencing a dip in success rate (according to our firebase...
Hey Nordic,
The following are some specifications of my project.
nRF52833-DK
PCA10100
Softdevice is S122
Based on "ble_app_uart_c"
SDK 17.1.0
I am using VSCODE...
While testing a new nRF9160 based product with a Hologram SIM card, it connects fine in Minnesota, USA, but not in Winnellie NT, Australia.
Do you have insight into why...
