This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Hi,
1. Since I need to use PWM DMA to transfer 320 bytes of data to the PWM for sequential playback. 2. I wrote the following test example to test the nrfx pwm driver, but...
Hey there, we are currently going through regulatory testing for a hazloc product. Our product includes an nRF52805 which is used for BLE provisioning and debugging of the...
Hi,
We are investigating a Nordic BLE DFU startup failure on iPadOS and would appreciate guidance on whether this pattern is known at the CoreBluetooth / iOS DFU layer...
How to change the parity bit on UART on NRF54L15?
prj.conf includes:
CONFIG_SERIAL=y CONFIG_UART_20_NRF_PARITY_BIT=y
DT overlay includes:
&uart20 { parity = "even...
Latest nRF connect for VS code seems to ignore Toolchain manager install dir under certain conditions.
nRF connect output displays " Error: Install directory 'C:\ncs' not...
Hi We are using nPM2100 with PG/RESET mapped to SHPHLD. We are using Zephyr library to manage the nPM2100. We put the device into hibernate with a timed wake up, if we wake...
Hi everyone! I wrote code in arduino IDE but wanted to use all potential of Xiao NRF52840 with use of Nordic SDK and Zephyr RTOS as well as zigbee on my small side project...
Device: nRF51822_xxac; the Nordic-supplied NUS application worked after I figured out the softdevice and application loading sequence.
Development platform: Mac OS Tahoe...
On lesson https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-4-bluetooth-le-data-exchange/topic/blefund-lesson-4-exercise-3/ , When trying...
Hi.
I'm developing a BLE peripheral application running on nRF54L15. nRF Connect SDK v3.2.1 with SoftDevice Controller is used for my application. As the title says, following...
Dear Nordic team,
We are using the nRF54L15 QFN52 package on our custom device and are using the P0.06 and P0.00 for the TX and RX, respectively, for our UART service interface...
Hi, I noticed that when using nrf5340 and it's kernel timer driver, that the k_cycle_get_64() API is not available, and that TIMER_HAS_64BIT_CYCLE_COUNTER is not being set...
Hi,
I’m planning to use a chip antenna that meets the attached specifications. I’m not very familiar with RF hardware, and I’ve only just started using CAD. I placed it...
I have a nrf52833 small board. nrf52833 QFN
and the several board have the same finding: at first time, the board can be flash and be debugged to main entrance.
but ,...
