Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
I encountered the error MPSL ASSERT: 1, 1310 when establishing a BLE connection on my custom board, only happens when using an external 32 kHZ crystal oscillator (
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL...
Hello everybody,
I have very bad problem for me. I am developing application on nrf7002-DK based on STA (station) example. I add own AT command analyzer and SCAN, so I...
Hello
Im trying to send data[3000] using USB, problem is I need to finish transfer within 13ms because after that period new data is ready to be sent. In this Interrupt...
Hi,
We have been working on our nRF5340 custom board with ncs V2.0.2.
Our application runs for 10 minutes to collect some sensor data and transfer it over BLE, then it...
Hello,
I am trying to do the current measurement for the 2NR EVK in sleep mode.
I am using the "Bluetooth: Peripheral power profiling" application that I was able to build...
I'm trying use nrf52810 as the peripheral to connect my nrf52840 central.
The hardware buyed from other vendor in local market, it looks very simple, maybe based on nrf52810...
my C: disc is full now. I need move ncs to another disc. for example:D:ncs
how can I do it. If I move all the files to D: with others's help , I find the setting user settings...
When the Thingy 91X is connected to a laptop via USB C, there is a drive available that contains a few files - config.txt, readme.txt, and an inf file.
Is it possible to...
I want to know the configuration of Nordic's GPIO pins. I only want to use one callback function, but due to the many buttons on my mouse device, it is not possible to configure...
When I was studying Zephyr, I found that some of the enumerations used by Nordic couldn't be found in Zephyr, so I was wondering if Noridc had encapsulated them in Zephyr...
Hello, as from title, after updating from ncs 2.7.0 to 3.0.2 my application cannot advertise and scan concurrently anymore.
If I start advertising after starting a scan...
Hello,
I would build the Matter nRF Connect Lighting Example Application from the SDK for the nRF54L15-DK. Coud you add support for it in the Matter SDK?
Regards
I am developing a custom USB module based on the nRF54L15 chip. I would like to know how I can initially flash firmware onto the board.
My plan is to have a custom bootloader...
