Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
I am considering a NRF52833 + nrf21540 combination. I see in nrf21540 product specification mentioned that
Single-ended 50 Ω matched input and output
...
Hello,
I want to create tfm_ipc project for NRF52840 DK board.
I configured options like below.
But I got an error message, "create_nordic_project.py failed (1)...
I looked at Blinky, but I am still not sure how to access the GPIO pins. In Blinky, there is an led0 alias, but what about other pins? What are there aliases?
Specifically...
Hello,
I used SDK15.3
Android phone and iOS phone is master
nRF52811 module is slave
It's said that the phone can't set conn international（Android、iOS）
But slave...
Hi,
i am working on "nrf52dk" . i want to use nfc pin as gpio.
what i did is
NRF_UICR->NFCPINS = 0<<0;
CONFIG_NFCT_PINS_AS_GPIOS included in preprocessor definations...
Dear Nordic,
I'm doing network registration test with nRF9160 DK in CMW500 test network environment.
I've set CMW500 configuration up as described at "https://devzone...
For a Non-RTOS application, take ble_app_blinky for example, the application is coded by us while SD is provided by Nordic.
My understanding is that the SD is running as...
Hello, All
I saw this description in the Bluetooth 5 Go Faster. Go Further document：
Advertising sets have an ID which is used to indicate which set a given packet belongs...
Setup:
Module: nRF51822.
SDK version:nRF5_SDK_11.0.0_89a8197.
Example: ble_app_uart.
Softdevice: S130.
I use ble_nus_string_send on the BLE_GAP_EVT_ADV_REPORT...
I'm following the NCS tutorials. I'm targeting the 52840 on the 9160DK board. I'm using SES with NCS1.6.
I'm able to get the hello world to run and the message is out on...
Hello,
we are developing a customer product based on the nRF9160 and Nordic's NCS v1.4.2 where we need to send battery test data every 30s (~ 1kB, PUT method). The communication...
Hi:
I am working on a stereo microphone application using the NRF52840. I would like to have the 2 microphones output 16K samples per second (8K samples each for left and...
