[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Describe the bug
When trying to sleep core on NRF52805 using low frequency internal rc oscillator, average current consumption is ~189.50 uA while when using external crystal...
Hi. We have nRF9160 DK using Serial LTE Modem as standalone modem for CAT-M1 connected with external nRF52 via UART2. We have setup the modem to establish connection to AWS...
I used the nrf52832-QFAA Reference Layout as the base design for the PCB.
The changes I made were:
1.) Added the DS1339 RTC Pin P0.22 will be configured SCL and pin...
Hi,
I am using nRF52840 dongle. The REG_OUT is programmed to 3.3V by default.
I am planning to use Li ion battery at VDDH. When the battery discharges below 3.3V, is there...
I have an issue when i am using an iPhone 8 instead of iPhone 7 , I can use iphone7 to OTA my BLE UART by NRF tool box, but ,when i useing iphone 8 , it does not work, what...
Hi,
Please advise.
I am using (nRF5SDK160098a08e2) , nrf52840 .
This is my code to change name in Runtime not via restart or timeout.
I call the function below every...
I'm trying to sniff BLE communicate data between the devices with nRF51822.
I have connected one device to the selected it with the interface toolbar. But I can't sniff...
Hello, I am using the ISP1507-AX and want to compile the BLE UART Mode Example "ble_app_uart_pca10040_s132" with SEGGER Embedded Studio in order to generate a hex file like...
Hi,
We have been working with nRF52832 and using BLE Mesh in our product. The product is an Access control reader which scans for nearby smartphones over BLE and sends...
Module model: nrf52832
SDK: 15.2
Hi,
I am trying to add custom characteristics to a custom service.
There are two ways that I am aware of:
a. sd_ble_gatts_characteristic_add...
I have a firmware version present SDK 13.1 and S132 SoftDevice v4.0.5 I am trying to do a DFU (just SD+BL first) which now has SDK 16.0 and S113 SoftDevice v7.0.1 But my package...
Hello, I have a issue about flash_manager module.
When I load a program on processor (that has been previously erased) there is a problem with initialization (flash_manager_add...
I'm trying to get a temperature reading from the on-chip temperature sensor on the NRF52832 - I know it is not a very accurate sensor but I still want to use it. I found a...
With IAR (EWARM) 8.50.9 the UART project in the SDK compiles fine.
After upgrading to IAR (EWARM) 9.10.1 or 9.10.2 I get compiler error:
Error[Go029]: Variable "sec_mode...
