I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Now we have a new project,in order to long distance communication,we add a PA RFX2411N in our design,now how may I tuning the pi (or T) match network between nRF52 chip and...
Hi All, What is the best way to modify ble_app_multilink_central and ble_app_blinky example codes, so BLE tag can send to ble_app_multilink_central Its own address. The ble_multilink...
My application uses a NRF52 (SD132, SDK 15.0.0), very simple circuit and needs to be extremely low current consumption. I measured the current in conditions of BLE on and...
Hi, I'm having some issues with migrating from SDK12.1 to SDK16 while discovering services.
It seems to connect to Android without much issue, but on iOS the connection...
A project is currently utilizing an NXP module to access the SD card via 4-bit SDIO. I am exploring the feasibility of integrating an nRF52840-based module, and have a few...
I am trying to use the battery example in " /ncs/zephyr/samples/boards/nrf/battery" to measure my 3V coin cell via VDD. I am using P0.14 to enable a set load on VDD before...
I'm using a nRF52840 DK (PCA10056 2.0.1 2020,14 683193023) with an adafruit FTDI serial TTL-232 USB cable (part number P70C uses the FTDI -FT232R chip inside a translucent...
i use pca20023-sr3_nrf52832_product_example demo to test, but there was an error occued , the segger rtt views displays:
00> [00000000] <info> app: System ON 00> [00000000...
Hello,
I'm in the process of developing the HW board for a nRF5340-based product. I need the customer could update the firmware using a serial port (USB or Bluetooth is...
I am testing a number of boards with a QSPI memory module with NRF52840 chip.
The QSPI driver functions all return without error even if the chip is not present. What is...
I have made PCB 32mhz crystal footprint with error. I have used other khz frequency too. Now I can't solder 32mhz crystal is it possible to code nrf52832 and control various...
Hello,
I wanted to test the long range, so changed the primary and secondary PHY to BLE_GAP_PHY_CODED from BLE_GAP_PHY_1MBPS in the advertising_init() of the peripheral...
I'm trying to debug a Zephyr application on nrf52DK. However, due to the use of multi-threading (in Zephyr) I can't use J-Link Debug Server (as I'm used to). For executing...
Hi,
Can you please answer below queries.
1. Do you support CIoT EPS attach without PDN connectivity optimization? 2. Do you support UE Usage Type (HSS and Samsung MME...
