Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello
I'm trying to maximize the throughput between a NRF52832 and iOS devices in both directions.
Currently, I seem to achieve about 400 Kbps from an iPhone 8 to the...
Hello, I Have been using your app Connection for Mobile to test my Heart Rate Monitor BLE, I am using also an Honor 9 Lite (Lineage OS 15.1).
The app Nrf find my monitor...
I would like to use the beacon example to send some manufacturer specific data over BLE.
I am using the nrf52DK , nRF5_SDK_14.2.0_17b948a and s132.
My question is other...
What's the fastest scanning settings for connecting to anywhere from 1 to 20 peripherals at a time? My peripherals are all advertising at 211.25ms. I won't be sending any...
Hi,
I am trying to use an SAADC converter to measure voltage in range from 0v to 3v5 but I cannot succeed. It is not possible to measure a voltage above 3V1. Well at least...
Hello, community.
I'm using NRF51822 SoC(256KB ROM, 32KB RAM) with S130 Softdevice.
I'd like to reduce the rom size and the ram size to decrease the production cost. ...
Hello,
I am using nRF52840 DK for bulding a bluetooth mesh. I would like to use JLink in board kit to flash and debug for other nrf chip.
How I can connect and configure...
Hi,
I'm using SDK 15.3. How do I connect a central (nrf53832) to another central (phone/laptop) using multilink central example? Its only connecting to other peripherals...
Using the 15.2 SDK, the stack generates an error when attempting to bond. I am using the android nRF Connect test app to initiate the bonding after connection. The error generated...
I'm using SDK 15.2 & HID keyboard example. I would like to know the following things-
1. How long does BLE chip advertise its name before making a connection with central...
Hello,
We're currently preparing for BLE certification of our device. It contains an NRF52840 on a custom PCB, so I believe we'll need to perform RF-PHY testing for certification...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
Hi! I develop board based on NRF52832. P0.08 is connected to the MOSFET transistor.
The transistor switches the relay. During start (power on or reset) on GPIO there is...
Hello,
Please let me check about the usage of an IRK for the default setting and how to change an IRK each bonding cycle.
We use the resolvable address for our application...
