hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Timer interrupt does not work well. In the code below, LED doesn't turn off and "interrupt!" message is not received. I really appreciate it if you give me any advice.
Hi Everyone,
I want to make a program code to establish the connection between MCU(nrf52832 chip) and accelerometer.
What are the conditions required? and i need some...
I'm using nRF52840 with SDK 15.2, and SD backend for Flash storage. I try to implement a verifiedWrite() method to write to flash. And it work most of the time, but fail sometimes...
Hi,
Is it possible to find comparison on the power consumption when running the internal DC/DC converter at 1.8V and 3.3V?
I have an external SD-card that needs a lot...
In the documentation for the s140_nrf52_6.0.0 I find the following statement: "The PPI channels and groups that are reserved by the SoftDevice when enabled are defined in...
MCU: nrf52840
SDK: V 15.2.0 porting with nRF-IEEE-802.15.4-radio-driver
problem:
ble_nus_data_send function sometimes returns BLE_ERROR_GATTS_SYS_ATTR_MISSING error...
Hi,
I am currently updating a firmware from SDK 12.1 to SDK 15.3 on a custom board using a nRF52832. Application itself has been upgraded and works well with Soft Device...
In the use nRF5_SDK_15.2.0_9412b96\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay，PCA10040. 1.Remove keys and leds from BSP。 2.Delete analog HRS timer...
hi all:
My project need 4 devices communicat with 1 host ,all use nrf51822 chip,is it possible？Now i have a problem ,when the third device communicate with the host ,will...
I have been doing some testing around DFU and I have noticed something strange.
My application size (according to nRF Connect memory read) is about 78 kB. (Left Image...
Hello,everyone,
I have successfully installed nrfutil using pip install nrfutil, but when I type nrfutil in the terminal, it shows -bash: nrfutil: command not found, how...
Hi,
We were trying out the long range central and peripheral examples found in github with the nRF52840 DK boards but we are not getting the specified range(We did switch...
Hi everyone, I have nRF52840 DK and I want to write an application program that uses multiple wireless communication protocols (e.g BLE , Zigbee , Thread) and can communicate...
Hi,
I am trying to add Nordic UART service(NUS) in ble_app_relay_rscs, but after adding nus service in application device is not advertising and there is no print in serial...
