I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello,
I'm looking for 3D STEP model of nRF52840 QIAA aQFN73 package. I just found step model of dev kit, but not component itself. Could anyone help me and share one. ...
Hi,
I was trying to follow the steps for this example: https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
However, I reached step 5, where I should compile...
Hi,
I am developing a bootloader for a custom board with the nRF52840 (nRF5 SDK v15.0.0 and SEGGER Embedded Studio V3.30) where we have no other option but to engage DFU...
Hi ,
I am working on application in which I am using GPIO pin to detect interrupt. GPIO pin normally has logic low level. When it becomes high level I have to generate...
We develop BLE server application on nRF52840 with SDK 1.5 using nRF52840-Preview-DK.
The application is built as multi tasks with freeRTOS where BLE is one of the tasks...
Hi,
I am using Keil uVision 5 and SDK 15 on nrf52840 development. NRF_LOG_ENABLED is set to 1 in sdk_config.h
But NRF_LOGS are not being printed in Debug(printf) viewer...
Hi,
when the micro go in: idle_state_handle(); I have 2 possibility:
If the soft device is present use the first instructions else the second.
This is correct, but...
Dear nordic,
I have an BLE application which works as Central and Peripheral and also which contain ADC,UART and GPIO's
Scanning and advertising controlled by application...
Hi Team,
We have observed that without power supply we are seeing 1V power at board Vcc. Without giving power supply to board.
Why is this happening?
We measured GPIO...
I was trying to verify boot loader using the provided script. I noticed following abnormality.
--It often fails to verify and show the following error:
Reading UICR...
Hi
I'm running nRF52840 MCU at 1.8V, and trying to use the dev kit (PCA10056) to program the external nRF52840 MCU.
According to the datasheet, the dev kit runs on...
Dear employee
for bug 89，
According to <nRF52832_Rev_1_Errata_v1.8>
It is mean below?(spi with blocking mode)
But I think it should be this
when transfer...
Hi Support ,
I'm estimating the average consumption of nRF52840 chip .
Regarding the BT consumption , I used the Online Power Profiler an got the results . But these...
Hello everybody, I've got some of nodes for the light switch example. I'm working on nRF52832 chips. I tried to find answear for my questions, but i didn't. I want to create...
