I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
I have a problem getting fstorage to work with BLE in SDK 14.2.0.
The fstorage example works fine until i change
NRF_SDH_BLE_PERIPHERAL_LINK_COUNT to more than 0
In...
Im am running a nrf528322 board with the s332 softdevice using sdk14.2.
I have implemented flash storage in my program according to the nordic flash_fds example. This works...
Hi Nordic,
I am using SDK 12.3.0 and S130 2.0.1. I have some questions about AFH.
1. Do Nordic stack keep track of some bad channels during communication and would skip...
Hi I am working on pcb design for a long range application with nRF52832. There are lc circuit which is implemented to antenna pins on reference design of nrf52832. I decided...
Hello,
I am trying to develop a custom BLE service. I have been following this tutorial .
I have also looked at this answer to understand the signal path for a WRITE event...
Hi!
I'm using SDK13 (Softdevice version 4.0.2) and I noticed that during an update via DFU bootloader the update of the Softdevice doesn't work.
After the transmission...
Hi Everyone
I have been trying to use nrf52840 on a custom PCB . So far everything is working perfectly except only one single issue which is the controller gets reset and...
I'm new to the NRF series, and for that matter Keil. I have a BT832A which is apparently an NRF52810.
I am able to flash my own code using Keil and and control GPIOs to...
Hello, I am battling with weird problem for 2 days already, need little help if possible, I have tried all remedies and nothing worked so far.
Here is what happened, I followed...
Hello,
I am using SDK5 for my code that builds successfully under Linux, but not under windows.
The error occurs in the SDK, not in the application. I am wondering what...
Hi,
We are trying to optimize the speed at which we send data over BLE UART with the nrf52832. Currently, we are using the ble_nus_data_send() function in a while loop with...
Hi, I am a beginner at this and I want to make a scroll wheel that connect to Android devices as an HID device. I have a custom BLE board from Skylabs (SKB569) with NRF52832...
I'm having trouble using the NRFX SPIM driver on the NRF52810 w/ Softdevice (S112). (SDK15.0.0)
I'm able to initialize but when I go to use nrfx_spim_xfer without the callback...
I'm trying to change the advertising interval for a non connectable BLE device, but this does not seem to vary regardless of the value set.
The code I used is:
#define...
