pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
i have one huge process one get positon sensor using i2c bus and another get led color also using i2c bus.
when color function is added in the process,positon sensor data...
Dear all,
I defined "DEBUG" , used UART peripheral and "printf()" in the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96. I find nRF52832 always dead in the place at...
Hello,
To determine the current network topology I hoped I could use the heartbeats to determine the RSSI and the number of hops. The RSSI of the last node is in the example...
Hi,
I found this example here for nrf51.
github.com/.../nrf51-ble-gzll-device-uart
And this is more or less what I would need for my application.
Is there a way that...
Hi All,
Scanning with a nRF52840 Dongle, Is there a way to know if one of the scanned devices is using Coded PHY modulation to advertise? And if the answer is negative,...
OS ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board CPU :(Nordic) nRF52832 / ARM Cortex -M4F 32 bit processor 28-pin Land Grid Array / 15GPIOs / SWD Soft Ver:nRF5_SDK_15...
Hi,
I am using "ble_app_uart" code and added battery service to it as custom changes.
I want to update battery level at every 3 seconds.
Code is working fine and starts...
Hi - In the examples provided, a peripheral will go to power off after completing its transactions.This means the the application does not have to "clean up" afterwards. ...
in pca10056.h, there are 4 buttons.
I want to add one new button, //#define BUTTON_5 NRF_GPIO_PIN_MAP(1,06).
However , it failed.
I debug and find the issue, #define...
i used SDK9.0.0 to implement the function that bond to cellphone.
case 1:when i set the IO_CAPABILITIES to BLE_GAP_IO_CAPS_DISPLAY_ONLY,the process of bond is ble device...
Hello,
i m using sdk15.2.0 in nrf52840.
please help for increase adv data size from 31 byte to 45 to 50 bytes..
i had tried with "BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
RTC connect through I2C and GPS connect to UART. I am getting large amount of data from gps contentiously . In the mean time i should read time from RTC . But i am getting...
i have 2 setups, one on a pca10040 running sdk 14.2.0 s132 and the other one on a pca10028 clone running sdk12.3.0 s130 with a 51822_xxaa mpu
the ble_uart examples from...
I just want a simple and clear PWM driver to generate a duty cycle on a GPIO pin - 25% on and 75% off. Just that. What is the most power efficient method?
The example PWM...
