[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version: 8.0.0
SDK: 9.0.0 IC:
NRF51822 Rev 3
service: NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi,
I am planning to design a new PCB and transition from using the Raytac module to our own custom PCB.
During my search, I found a design that includes an SMA connector...
Hi, What I noticed is that every time I want to flash the nRF9161dk I need to do `west flash --recover` for it to work. I am flashing from Mac M1 (Sonoma 14.5) with `West...
nRF51822QFAC SDK v10 S130
In the completed project it was necessary to make an update. It is necessary to switch off the softdevice and switch to its own Rx protocol. After...
Just purchased a nPM1300 v1.1.0, but it will not connect to my computer. I am using version 2.6.1 of nrf connect, v1.3.0 of the PowerUp app, and what I believe is the correct...
Once the modem is turned off (e.g. using at+cfun=0) - what will be the state of the MAGPIO pins? Will they be pulled to GND or will they float?
Thanks
Ulf
P.S. The same...
Hi,
I am trying to implement the scan delegator in the broadcast_sink of the nRF5340 audio application.
Currently, I am adding the advertising feature in the broadcast_sink...
Hello, Our application image became too large for TF-M and we're investigating the use of PSA Protected Storage without TF-M as described in NCS 2.6.0.
When writing a new...
Hi,
I encountered a modem fault (NCS v2.5.1, mfw 1.3.4, nrf9160DK). Here's a portion of the log leading to the fault:
[24:36:01.333,312] <inf> gnss: event NRF_MODEM_GNSS_EVT_PVT...
Hello!
I am a beginner and am trying out an MQTT example on my nRF9161 DK that I recently bought in my Visual Studio Code on Windows 11. I am aware that the sample application...
Hi,
I am able to get my CA certificate working using TLS for MQTT. but im not able to get the TLS Client certificate working.
I had created a client certificate as per...
Hello, I'm following along the nRF Asset Tracker guide and I'm on the step 'Create device credentials'
Running the command
' ./cli.sh create-and-provision-device-cert...
Hello support.
A new design is looking at using nRF24L01+ to communicate wirelessly. I'm aware that this IC is no longer recommended for new designs, however, it's the one...
Hello,
I am trying to use the LTE modem serial example on a customized board that communicates an NRF9160 SICA B1 with an external STM32 microcontroller through the UART...
I am using the nRF52840 with NCS SDK v2.5.1. I tried to implement non-volatile storage in my application, and it is working on the DK board, but the code is not working on...
Hello,
I am using the DK Buttons and LEDs module to get the status of my button on the ANNA-B402C ( nRF52833 ).
I wanted to check if any debounce filter/mechanism software...