Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
I am attempting to stream data in chunks of 65535 bytes from the nRF9160 using data mode from the 2.6.1 version of serial_lte_modem sample code. The nRF9160 receives AT commands...
Hello,
I am purchasing a RAK4631 module, and am looking for an alternative for the J-link single step debugger. I saw that this product had a o n-board SEGGER J-Link debugger...
Hi ,
I am exploring the peripheral examples from the nRF5_SDK_17.1.0.
I am testing the example code "flash_fds" from the peripherals. I am able to compile the code without...
Hi
First the fundamentals, I am using:
nRF52840-DK
nRF Connect for VS Code: v2024.7.13
I am trying to create a demonstration project, where I need both SPI and...
According to developer.nordicsemi.com/.../migration_sysbuild.html , the config variable SB_CONFIG_BOOT_SIGNATURE_KEY_FILE and SB_CONFIG_BOOT_ENCRYPTION_KEY_FILE should be...
I'm working on porting an existing product based on NRF5 which uses the nrf_twi_mngr with asynchronous calls in its drivers. The drivers takes advantage of the non-blocking...
Hello,
I have a custom board based on a nRF9160 SiP. It uses a shared antenna for GPS and Cellular, based on this : https://infocenter.nordicsemi.com/index.jsp?topic=%2Fnwp_033...
Hello,
Installing a new computer with de dev environnment I am finding that NCS1.9.2 is not in the available releases.
Is there a reason for this?
Thanks for...
Hi,
I have a customer in Guernsey that received one of our Thingy91 hubs and he's not able to connect.
Here is some troubleshooting facts :
- when he moves to London...
Hello,
I just received a new NRF9160-DK board and I am surprised it has the 4 leds blinking all along.
What does that mean?
I have not found any of this in the startup...
Hi everyone,
I'm currently working on a project involving an Ember ZigBee end device and a Nordic ZigBee coordinator ( Nordic nRF52840 donngle) . I’ve encountered an issue...
I need to use UART0 of the nRF9161 via Tx(P0.27) and Rx(P0.26) for serial communication. There is no CTS/RTS signal.
I used the code from Lesson 5 of the DevAcademy. i...
I'm developing with nrf connect sdk.
I have an peripheral IC with a mcu interface enable pin. This product is very focused on battery life. The peripheral IC has higher...
I am working with nRF Connect SDK 2.6.1 on a Central and a Peripheral and I am running the BAP similar to the nRF Audio Example. I am using out of band pairing over UART for...
I try to migrate a working code from nRF52832 to nRF5340 with the use of 7002 companion chip for the network part (BLE). However, while I can jump to main and successfully...