if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
Hi Team,
I am trying BMI270 Sample using nRF54LM20 DK. But the problem here is it getting exited after checking the device is ready section.
Added my overlay file for...
In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
nrf sdk 2.9.2
I wanted to stop Bluetooth activity, so I used `bt_disable`, but a kernel panic occurred.
So I create a simple example to try this function, I still get...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Using the flash : https://datasheet4u.com/download_new.php?id=1588116 on SPI : XF_CS (P0.13), SCLK (P1.09) , SDI (P0.08) , SDO (P0.05) Flash specific parts in the nrf52840dk_nrf52840...
I have recently purchased nRF52840 dongle which I wanted to use as a ZigBee sniffer. I bought it on AliExpress and it supposed to be original Nordic board, but it turned out...
Hi everyone,
I’m trying to program/recover a custom board with an nRF52840 Fanstel module using a Nordic nRF52840 DK as the programmer. The board is powered from a 4.2 V...
Dear Nordic Support Team,
We are developing a Matter device based on the nRF54L15 using NCS 3.1.1 . We started from the Matter light example provided in the SDK.
We encountered...
I have a combined asset_tracker_v2 and central_main. I can connect perfectly and receive data from a single BLE advertiser. I need to be able to connect to 1-4 simultaneous...
Hi,
I’m using an nRF5340DK with nRF Connect SDK 2.9.1 , configured as both Central and Peripheral with the nordic SDC running the network processor Goal: allow the board...
The firmware always halts execution during boot after providing these logs:
26/05/22 10:38:33.925 89737.861 13892 0 E: Device id 00 00 00 does not match config 1f 16 01...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
I’m working on a custom board based on the nRF9160 (SICA variant) and trying to enable MCUboot + TF-M with sysbuild. I’m running into an issue where the system never reaches...
I’m using the RADIO peripheral for BLE 1M connection-event RX→TX turnaround.
Current flow:
1. RADIO receives a data PDU. 2. RADIO reaches END/PHYEND and disables. 3. In...
