[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi Folks,
As per bluetooth spececification(4.4.2.2.1) advertising interval has addition of advDelay in range of 0-10ms. In my example,
1. device advertise beacon (sd_ble_gap_adv_start...
Development Kit: NRF52840
IDE: Segger Embedded Studios
I'm trying to use the nrf_drv_twi driver in my project. I've included the .c file in my nFR_Drivers folder. My...
Hello,
I am using the nRF52840 DK board and with Softdevice code nRF SDK 17.0.2. I am trying to write custom advertise data with custom type.
As you can see in the above...
Hi! Hope you are all doing well,
I'm having trouble making a project from scratch, I'm basically trying to filter bluetooth devices by manufacture code but I'm afraid that...
Hi All,
This has happened before so I know it's a handler error.
But this time I'm pretty sure my handle is not wrong, can help me?
in main.c =>
Best regards...
Hi,
Can you confirm the appropriate method to doing AFC correction for a GPS SNR test using the %XRFTEST command and then using the AFC correction result in the GPS SNR...
I use SPI to develop motion sensors KX022 and DW1000. The first digit of the received data is always 0xFF. If the first byte received is removed, it can be used normally....
I am trying BLE MESH light switch example with nRF5_SDK_for_Mesh_v5.0.0_src using nRF52833 DK. In the light switch example, server SDK is working fine and I can see the provisioning...
Hi All,
I am using Custom 128-bit UUID, My application need 3 Custom Services and 20 characteristics. But I need to make different Base for services and characteristic...
Hi,
I recently installed v1.9.0 SDK and while creating project from sample applications I am getting below error.
Attached is build logs from segger IDE.
Can anyone...
I'm looking to build a custom bootloader for my NRF52810 device. I'm developing on nrf sdk 17 with SD 112. I will be leveraging the secure bootloader example and re-using...
Hi;
i am using sdk 17.0.2 and mesh 5.0.0.
i am using light switch instance.In addition, the system works properly when provisioning is made with a smartphone.
I want...
I am using VSCode and the NRF Connect SDK
I can build and flash my device however i keep getting cannot open source file for all my includes, i also cannot navigate to...
First, NRF52833 work environment at 100 degrees celsius, standby current reaches 60uA.
Second, When the NRF52833 working in 100 degrees Celsius, what kind of processing...
I have a secure BLE DFU project that is basically a duplicate of the example project (secure bootloader pca10040_s132_ble). I am able to flash a merged hex on my custom board...
