In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi,
I'm using the flashlog on my nRF52840 to log events. I have an external RTC which I read when logging each event in order to timestamp the event. My RTC code writes...
I am trying to set up a project that uses MCUBoot and puts the secondary slot into QSPI External Flash. I'm using NCS 1.7.1 with VS Code. I've followed numerous posts on these...
I am currently evaluating the differences between nRF52811 and nRF52810. I am still using the nRF5 SDK.
One difference is in the nRFInitialize function in the startup code...
Hello,
In my application (using sdk 16.0.0) I have a bootloader that allows to upload a new firmware through either BLE or UART. The Bootloader is initialized as usual:...
Hi All!
I have a problem running simple PWM output on NRF5340 board. I have a following code:
Now what i'm trying to achieve is to get 50% of duty cycle with frequency...
Hi there,
This should be straight forward but has me stumped. I'm trying to add BLE to my CAF based application and can't do and recreated the same problem with the samples...
Hello, I have a two part question with regard to SPIS setup time when exiting low power mode on an nRF52840.
We are using the SPIS peripheral on an nRF52840. General guidance...
Hello,
I am currently integrating the Wiznet5500 drivers into a VSCode project, but I am stuck on where to include these custom modules.
In the previous version in SES...
Hi，
I have a problem about CAF leds modules. I submit a led event to turn on led for 3600ms and turn off led for 500ms, but it work inversely in fact.
I find that leds...
SD140
Part nrf52833
Application: Central App that connects to 1 to 16 different peripherals. One at a time.
Problem: 1/10th of the time, I get a disconnect reason BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED...
I keep getting a hard fault when calling spm_request_random_number()
I'm following the secure_services sample provided in the SDK, and the secure_services header file...
Hi, I am using the nrf52 Thread v4.1.0 SDK for development
I am using ADA4333
there pin 6 is used for Gate control but
in CLI pin 6 is used as uart tx
and it is hard...
I found the following problem with Programmer v2.0.1, using either a Nordic DK or a Segger J-Trace as the programming device (on Mac OS 11.6, and with nRF Connect 3.9.1):...
Dear All, I am trying to add the task watchdog to my application, but I am dealing with some interesting issues. The NRF SDK that I am using is the v1.6.1 I have dealt with...
Hey,
I saw the example in the SDK for hid keyboard over ble but it is only as a peripheral device.
In my project I have the nordic board as a central device connecting...
