Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
We have a device that is using nRF9151 for LTE-M and GPS. The device has 2 versions, one with U.FL and other with chip antenna with matching network.
During testing we found...
Hi Nordic,
I'm using custom board based on nrf52840 SoC. After migrating the SDK, the original device tree configuration for ADC became unavailable, but I failed to find...
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
A number of phones seem to now offer channel sounding support. (Pixel 10, for example). Do we know what antenna configuration they have - i.e. one or two antennas to enable...
Hello,
Our company has developed hardware using the nRF52840. We are using nRF Connect SDK 3.2.1. We have a developer that has been working on creating a mobile app using...
Hi Nordic,
I am currently evaluating the nRF9151 SMA Development Kit for a Non-Terrestrial Network (NTN) project and would like to inquire about the available NTN-enabled...
Hi
I have read that the J-Link OB on nRF DK's can program nRF's other generations that the one on the DK itself by using the J-Tag output connector. But does the J-link...
I want to pass a variable to my program so I'm using the command: west build -b nrf52840dk_nrf52840 -p --build-dir build -- -Dmy_variable=40 Then in my program I want to print...
I'm having some issues creating multiple LittleFS file systems on a project. This is part of a larger project, so I used the Zephyr LittleFS test code to create a demonstration...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Trying to work thru the dev academy exercise 2 using v3.2.4 SDK. I presume this should work because the readme says must be greater than v2.8.0 for thingy91.
I made all...
We are using the legacy 17.1 nrf sdk with the nrf52840 MCU in tickless idle mode and notice that after about 10.5 minutes the current draw jumps from ~90uA to ~277 uA.
There...
Hi,
We are working with the nRF54L15 using nRF Connect SDK v2.8.0 and would like to enable the secure boot feature.
However, it appears that the SMP Server sample in...
I'm using put all together 2 sample
a) NUS Uart that is used for the configuration;
b) zephyr/samples/net/opentread/coap Using the nrf5340dk/nrf5340/cpuapp.
The compilation...
Hello,
Step 5.2 of this part of the course has a code example which shows which i2c node to use to control the temperature sensor. In the case of the nRF54l15DK it is...
