Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
How much is the temperature characteristic improved by setting CALIBRATE OFFSET for nRF52832? How much does CALIBRATE OFFSET improve the temperature characteristics?
Are...
Hi. In other discussion I have seen pairing/bonding should store all necessary parameters of a discovered service. It's possible then to reconnect to a bonded device without...
Hello,
I have a security issue with a product with nr52840 because if a hacker connect to my device with nrf toolbox for example, when i stop the bluetooth connexion on...
Hello, I've been working with unit tests lately, and got the example unity project to run (from here ). Now I encounter some issues when integrating it into another Zephyr...
I use usb with secure bootloader to flash 52833/840/832 boards. Is there a way to use the nrfjprog --memwr/rd over the usb after a DFU on USB upgrade to new app?
Steps w...
Hello,
I have an analogue audio mic connected to external ADC. The external ADC can give an output of 16bit, 20bits, 24bits and 32 bits I2S data. I have configured to send...
All the SDK health device examples appear to have a rather complicated relation between the BSP buttons and the behavior of the device (advertising, connected, etc.) which...
Hi Everyone,
I am having some trouble on nrf5380 PDK. I can not connect it to my PC.
I attached photo of nrfconnect.
There were 3 serial ports but I have used just one...
when using the TIMER, I set the TIMER's time_ticks=53328 which means that every 3.33ms, the TIMER will call its callback function and start ADC sample. However, when I use...
Hi.
We are evualuating and testing NRF9160 DK and after a while testing and reading different threads of the forum I know the mode GPS + LTE in the nrf9160 only work in...
Hi. I'm using external board with nRF52832 and GPS. (SDK15.0.0)
I used ble_app_uart example and succeed in receive data in my nRF UART v2.0 app.
I got this kind of data...
Dear all, Im experiencing the following error that pops out on RTT console during the first few lines of main():
I understand the definition here: https://infocenter.nordicsemi...
This is my code:
This is the results of the logs in the code:
<info> app: tx buffer length = 8 <info> app: AA <info> app: FF <info> app: 10 <info> app: 08 <info> app...
