Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
HI
I'm having an issue where VS Code cannot recognize the SDK and toolchain. Everything was working fine before, but now errors occur when I open VS Code and try to build...
Quick qestion
Making a new board with external memory(jedec) and using S QSPI as I have to put it into cpuflpr_vpr(does not work with QSPI). Works fine !!
but I also plan...
I note with interest that Nordic is providing support (e.g., downloads) to run CircuitPython 10.1.4 on various Nordic devices, including the nRF54H20-DK . I've just received...
Hi I am able to load the nrf9151dk_at_client example hex on my custom dev board . I try accessing the AT commands and I can very easily get the responses. I want to install...
I'm using nRF52832 SoC with nRF5_SDK17.1.0 and SoftDevice v7.3.0. I'm using following code to write data into flash.
err_code = nrf_fstorage_write(&g_fs, write_addr, buffer32...
HI，
I am currently conducting secondary development based on the periodic_adv_conn sample in the ncs 3.2.1 SDK . Now I want to add continuous carrier wave output and continuous...
I work on nrf connect sdk v3.2.4(nRF54L15).
I plan to run the main application on cpuapp and the device control application on FLPR. It's currently working fine. In the...
I'm currently testing an app, which was running with a nrf9160/mfw-1.3.7/NCS 2.9.2.
Running this app now with nrf9151/mfw-2.0.4/NCS 3.1.0 seems to get a smaller response...
Hello,
I previously opened a ticket describing an issue where using MCUBoot in NCS v3.1.0 caused the GRTC to reset after a sys_poweroff() .
As discussed in that ticket...
Hi,
I am working on the XIAO BLE SENSE board which has nRF52840 SOC with P25Q16h 2MB flash and other sensors
I want to access the external flash to store sensor data....
Hi Nordic Team,
I am currently developing applications for custom boards using the nRF Connect SDK v2.6.0, focusing on the nRF52840 microcontroller.
In our ongoing project...
Hello,
I am using the nRF54L15-DK development board running the official hci_uart example as the BLE controller. My own Linux system acts as the host using BlueZ to control...
Hi Nordic team,
I noticed that when using the external FEM (nRF21540) with the nRF54L5 device, the power consumption at a transmit power setting of 8 dBm is significantly...
Hi, I have implemented a soft UART in the VPR FLPR. I am having trouble power managing it. I see an unexplained extra 500 uA current draw after I start the CPR until I reset...
