Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi,
I try to implement the nrf52832 as the TWI slave but get the following error messages:
I have added the nrf.twis.c to the project, included in the main application...
Ummm. :)
I'm hoping that I've done something silly.
It looks like I'm unable to configure a project.
Because the save option has vanished.
Another observation...
I am developing a Central/Peripheral application with SDK 15.2.0 for s132 device on nRF52 development kits. I switch back and forth between my application and the example...
Hi, I'm having a bit of an issue with the proxy_enable() & proxy_start() functions when they are used in tandem with the flash manager module.
Some info on my setup:
...
I would like my BLE device to communicate with Desktop using HID service & with a phone using custom gatt service. I know its just adding one more service but is it possible...
Hello All,
I'm trying to create a client device that toggles LEDs on a server on and off using the NRF52840-DK.
My modified Client code is giving me Mesh error 5 when...
In which state are the configured UART pins if the device is held in RESET for nRF52832?
We want to use the UART to communicate with the host without the nRF52832 in certain...
Hi, I have a project where an STM32 controller has the updated binary file for nRF1822 in flash and it will upgrade the firmware on nRF1822 with the serial implementation...
I am trying to add "Softdevice_handler" to project under nRF52 SDK_15.0.3
But i couldn't find "Softdevice_handler" in nRF SDK_15.0.3 and it is there in SDK 11
How to add...
Good afternoon,
The 'sd_ble_gap_device_name_Set' seems to have a limit of 10chars when defining the device name. In principle, it should be 31. Why do I have this limit...
Hi
I would like to use a 2.4Ghz remote controller for a project but I did not find any example/documentation on how to use 2.4 frequency with my nrf52.
Can someone...
Hi
I would like to use a 2.4Ghz remote controller for a project but I did not find any example/documentation on how to use 2.4 frequency with my nrf52.
Can someone...
nRF52840-DK 2pcs, one TX broadcast signal software, one RX software. RX can receive TX.
My nRF52840 product 2pcs, one TX broadcast signal software, one RX software. RX can...
Hi,
I am working with a motion sensor which sends a message when it detects a motion. I am communicating between the nRF52 DK and the sensor via UART. I am able to receive...
Hello,
I am interfacing nRF52840 DK with the MAX30101 sensor. I am able to execute all the TWI transactions necessary by using port 0 pin 27 as SCL and port 0 pin 26 as...