Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi
I am working on Eddystone in nRF52832. Its working fine when using power supply.Then I used Lithium battery as VDD. then it not working properly, only working in connectable...
Hi,
I was wondering what is the recommended GPS circuit would be for an always outdoor device with a large patch antenna, without the need for an amplifier. Would the following...
Hi all,
I have my custom nRF52832 board, I use SDK12.3.0 with SD132.
I'm currently trying to add BLE advertising to my firmware. To achieve that I'm copying parts of...
Hi,
I am performing the following test:
https://devzone.nordicsemi.com/nordic/b/blog/posts/testing-long-range-coded-phy-with-nordic-solution-it-simply-works-922075585...
For my graduation project i'm developing an improved version of the Nordic Secure DFU Boot loader. I'm trying to integrate something like the Zigbee OTA client inside the...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
1) Initially by seeing register description I thought each TIMER has its only...
Hello.
I imported the "Nordic_UART" example from "nRF5_SDK_15.2.0_9412b96 examples ble_peripheral\" The device is visible from the Android BT settings and is not visible...
Hi,
I am now working with the iBeacon. I am trying to get the RSSI @ 1m distance.
I am able to get the major and minor and the tx power but cannot access the manufacturer...
Hi,
I wanted to build a single shot timer using the nrf_timer library. I went into the library code and I couldn't understand some of the enumeration due to some lack of...
Hi,
I'm using the USBD for HID keyboard on my nRF52840 and I'm trying to change the serial number. On my PC (Linux) the Serial number always appears as 0 using lsusb -v...
Hello there!
I'm developing an nrf52810-based device, which needs to be as small and simple as possible, pretty much like your nRF51822 Beacon Kit.
I've founded the nrf52...
I successfully tried the "beaconing" example from your Mesh SDK 310.
I noticed that moving
line 215 "adv_start();" in main.c
right after "ERROR_CHECK(mesh_stack_start...
Hi, I am using nRF5 SDK for Thread and Zigbee v3.0.0, and I want use NFC pin and RESET pin as inputs.
I wrote in my .emProject this preprocessor definition "CONFIG_NFCT_PINS_AS_GPIOS...
