[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hello,
I am designing a wearable using the nRF52810 chip and would like to ask if there are any recommended touchscreens to be used? My main concerns are
SPI bus (at...
GCC linker is capable to generate elf file with a given value for UICR->APPROTECT register with a simple script:
This feature allows generating "always protected firmware...
i'm using this dongle USB840F based on nRF52480.
i'm using usbd_ble_uart_freertos (SDK 15.2) example, the usb port is detected and i can read from it , but it doesn't advertise...
Hello
I'm surprised to see this kind of power profile when the device is in advertising mode.
The 3 TX steps for the 3 canals of advertising haven't got the same max...
Good day,
I wish to adapt the Eddystone Beacon example for nRF51822 with S130 in e.g.:
..\nRF5_SDK_12.3.0\examples\ble_peripheral\ble_app_beacon\pca10028\s130\armgcc ...
In my application, the nRF52840 dongle is hard-wired via UART port pins to the UART interface of a Wi-Fi gateway host board. I need the nRF52 application to restart when it...
As a final step to the legitimate dual bank-based application DFU , the existing application will be replaced by the new application.
What happens if an internal error...
Hello,
Is it somehow possible to output a 13.56 MHz signal from the nRF52 ?
Yes, I KNOW: Similar questions have been asked many times. The nRF52 cannot drive an 13.56Mhz...
Hi,Nordic Teams:
I have emergent proble ,can you help me?
1.in light_switch example provisioner,there is some code below:
2.when provisoning ,we can setup a node to...
So I run SDK 15.0. I have a notification channel, and I want to transmit some data on it.
I run this code
hvx_params.handle = gatt_notify_handlers[index].gatt_handle;...
I'm using the nRF52840 to interface with an existing 802.15.4 network. For reasons decided long before I became involved, the messages exchanged are MAC command frames, not...
Hi,
I am testing BLE throughput between NRF52832 and iPhone XR using S132 stack. I am able to get maximum of 400Kbps. Is there a way to achieve throughput better than...
Hi,
I am trying to design the transmission lines based on the reference board design from Nordic.
I opened up the Altium layout file for the board which I downloaded...
I'm trying to communicate with HTS221 sensor and read WHO_IM_I but then I always get error 17 on nrf_drv_twi_rx and receive 0 on output
Twi init
ret_code_t ret;
const...
