In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hello, I'm new to this devices. I have several NRF52840 devices and i want to connect them to a Raspberry PI via BLE. I'm not using sensors yet, I just wanna establish a simple...
Hi,
I use nRF5 SDK v15.0.0. In my application I need to change Bluetooth identity address. I can not use BLE_GAP_ADDR_TYPE_RANDOM_STATIC address type, because I need to...
Hi,
I have migrated my projekt from SDK 14.2 to 15.2, the bootloader is basically the secure_bootloader example with some tiny adjustments. When I try to upgrade my product...
Hi all,
I encountered problems porting MbedOS based software which uses Bluetooth Low Energy from MbedOS 5.10 to 5.11 to use the extended features od BLE 5.0.
The ble...
I have interfaced two Nordic nRF52840 boards with one as master an other as slave .
In the image attached signals from down depicts Salve seelct,SCLk MOSI and MISO of Master...
I run into problem, I think for now resolved, but questions remain: Do I have to stop BLE whenever changing ADC config? What did not work?
I don't know why it does not...
Hi, we made a custom board with nrf52832 and flashed example code experimental_ble_app_blinky from sdk13.
We are trying to change the radio txpower other than 0db (default...
Hi all,
I have a nRF52840 development kit and flashed (I believed it flashed successfully) with direct test mode .hex file from SDK 15.2. What I facing was not able to run...
NRF52840 - SDK 15.0 + Some register based custom functions. S140, 6.0.0. In order to work around some of the hardware limitations with SPIM in the context of a project, we...
The PWM Driver has all sorts of fancy stuff for dealing with clever sequences - but I can't see anything to just set a simple, steady, fixed duty cycle!
How does one just...
I need to configure 2 devices as relay nodes in order to relay messages from the client node to the server node
How can i implement this in the light switch example ?
I know this has been asked a few years back, but wasnt sure if there were any changes to this. I want to be able to detect when a connected device is removed from windows...
Hi,
I use nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10040_ble bootloader. I upload my app to my board using PCA10031 and nRF Connect v2.6.2 on Win10 and...
Hello,
Our board is based on nRF52832 with S132 5.1.0, without RTOS. Now we have a requirement to protect sensitive memory areas with MPU, so I'm trying to run firmware...
