I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
How should the addressing be between an nrf24LU1+(transmitter) and nrf24l01+(Reciever) in the code.?
The registers TX_ADDR, RX_ADDR_P0, RX_ADDR_P1 are updated on a device...
Do we need to explicitly set the ENABLE field (Bit31) of RADIO->OVERRIDE4 when applying the override values from FICR->BLE_1MBIT[n]?
From the few samples I've checked,...
Please teach me the minimum theoretical value of the transmission time in the following conditions.
CPU --> nRF24L01 --(2.4GHz/1Mbps)--> nRF24L01 --> CPU
CPU -->...
I need to send a long (let's say 10Kb) notification from Bluez 5.37 on my Linux device to a mobile phone.
My implementation is based on src/shared/gatt-server.c .
I...
Hi,
I have put in my chip (nrf51422):
-1 softDevice s110 8.0.0;
-2 application (hrm_whit_dfu);
My problem is:
when i send characteristic to start advertising the board...
Hi everyone,
I am new to nRf series and have just started to use the nRF51 Development kit(nRF51422). I am using the s130 softdevice and I have seen that the sofdevice supports...
I'm trying to test out pin change interrupts using the PCA10028 dev board. I'm using two buttons to turn off and on an LED. The code below is only generating events from button1...
I have a custom board designed which implements a Arduino Micro (ATmega32U4) and an nRF8001 chip based upon Richard Clarks' nRF8001 breakout . The Arduino FW uses a slightly...
Hi.
Is it possible to enable the encryption of data which corresponds to the particular characteristics? i tried with BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, for setting the...
Hi,
how is the new nrf_drv_twi supposed to be used for reading registers?
The sequence for that is pretty much industry standard:
> Device address
< Ack
> 0x00 (register...
I'm running the ble_hrs example provided on my nRF52 board. The thing is, I'm unable search my device using both nRF Master Control Panel and normal Bluetooth connection from...
I am using a central S130 softdevice in an nRF51822. I connect to a peripheral using sd_ble_gap_connect(&m_peripheral_address, &m_scan_param, &m_connection_param) . If it...
I am trying to provide a custom peripheral service with a 128-bit UUID in an nRF51822. I would like to use two bytes of the UUID to encode a piece of information unique to...
Hello,
am I right to assume that if sd_ble_gattc_write returns anything other than SUCCESS, then the packet was not queued?
Is this also true for BLE_GATTC_EVT_WRITE_RSP...
