Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Want to store the CONFIG_BOOT_SIGNATURE_KEY_FILE in the project space, not the ncs folders.
Looking for a method to define file location without using a absolute path. ...
I am using NCS v2 and VSCode extension on Windows 11.
I have two pieces of hardware I am testing with:
Adafruit nRF52840 Feather
Custom nRF52840 board
When I flash...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I would like to automate some unit tests with NCS. I tried running the native_posix qemu builds, however, this does not support the mac m1 architecture (maybe Linux only?...
I'm updating the NCS we are using from 2.0.2 to 2.1.0 in order to use the modem firmware 1.3.3 that was just released. I verified my build with NCS 2.0.0, 2.0.1 and 2.0.2...
Hello!
I use NRF Connect SDK 1.8.0, but peripherials are configured using nrfx library.
My task is to implement serial interface where I have PIN_TX and PIN_RX. I transmit...
Hello All,
I have few questions below:
- Does the ENABLE input disconnect the internal power systems completely, or does the circuit remain in some mode and nevertheless...
Hi Sir,
I am testing the NDT w/ example "nRF_DM" (NCS 2.0.0), there are two nRF52840-DK for this test. When two boards link success, the terminal starts to show the log...
Hello everyone
In the company I work for, we make a special kind of dongles which are able to connect to smartphones through BLE and transfer data.
I have 4 of these dongles...
Hi there,
I am working on a door lock project using nRF 52840 DKs and nRF5 SDK for Thread and Zigbee v4.2.0. we are having both ZigBee and BLE protocols in it. I started...
Hi everyone,
I'm trying to implement directed advertising on the BLE codeded PHY.
My setup of consists of two identical NRF5340 based custom boards, running FW based on...
Hi, nice to e-meet you. I want to use nRF52810 pin 25 (or other pins) to drive an external board, and through it to control the external board switch.
I set the pin to H0H1...
Hello,
I am currently working with pc-ble-driver-py and have observed write operations taking an exceedingly long time. Previous DevZone posts on this topic seem to be unresolved...
Hi,
Sorry to seek help again but I cant solve this issue
Steps
1 - nrfjprog -f nrf52 --eraseall
2 - nrfjprog -f nrf52 --program mbr.hex --sectorerase --verify
With...
