I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I am using an nRF520 PCA10040 dev board with a nRF52832 module and I am trying to get the ble_app_uart_pca10040_s132 FW to run using the SES segger tool set. After about 1...
Still having trouble getting a simple Blinky example running on two nRF52840 DK boards configured for a long range PHY_CODED connection.
I've looked through this post -...
I am new to the Nordic SDK and Segger embedded studio, and I am trying to test my NRF52840 dev board.
I am running the "ble_app_blinky_pca10056_s140" example, and I want...
1. Background info
We're developing a new IDE for microcontrollers (see https://embeetle.com ) and would like to support a range of Nordic Semiconductor microcontrollers...
1. Intro
We're developing a new IDE for microcontrollers (see https://embeetle.com ) and would like to support a range of Nordic Semiconductor microcontrollers. We received...
Hi,
In case of nRF52810, is it possible to implement both Master and Slave Mode ?
Also, this has do be done while the product being able to work with AT Commands.
...
Power Profiler V2.3.1
Hi,
I recently started doing power testing on one of our boards using the power profiler kit. I wanted to tested current consumption at different...
Hi Nordic Community,
I am trying to build a network using the OpenThread protocol and the nRF52840 chip. I have several Dongles, but I can't figure out how to flash the...
I'm importing ble_app_blinky_pca10040_s132 example in segger IDE. I'm using EVK-NINA-B1 and from nRF SDK I'm trying to importing example but getting error as mentioned in...
I have an external clock running at 3Mhz which I'd like to align with in software. Consider this contrived example:
What would the consequences be of attempting to read...
Hi,
I'm very new to c programming and your hardware. Please excuse my novice questions.
I'm making a rotary braille display using nRF52840 dongle (PCA10059) as it's brain...
Hi,
I using custom nrf52840 board .I have loaded the Bluetooth program in to the custom board using swdio/swclk/vtg/gnddetect these lines.There is no problem in Bluetooth...
I'm attempting to get MMD set up in an IAR project following this tutorial: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/monitor-mode-debugging---revolutionize...
Dear sir, We are using BL654PA from Laird technologies. We want to check RSSI at 2402MHz, 2440Mhz, 2480Mhz. Can you guide us how to enable PA without using Nordic stack file...
Hello,
I'm using a Thread Border Router built using a Raspberry Pi 3 and a nRF52840 Dongle. I followed the steps at this link: https://infocenter.nordicsemi.com/index.jsp...
