hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I was wondering the behavior of the NFC BLE Pairing with OOB when max connections are full. Will the connections disconnect in order to pair with a new central after an NFC...
Hello,
in nRF52832 devices, P0.21 pin can be configured as reset using PSELRESET[0], PSELRESET[1] ergisters.
Due to space constraints, i dont intend to use the reset...
Hi：
I want to ask：the nRF24L01 can work in single point mode by SPI commands。 I need the wave show like in the picture。
IF it can,which software and hadware I need....
Hi,
I trying to send indication supplied with some data to my Android app (which BTW works fine with other BLE devices) as an answer to characteristic write command
...
I am trying to run a project on a Fastnel
BT840 module
I had the code running on The dev kit when we switched to the new hardware without a FL crystal I have been unable...
Hi,
I am working on writing data on flash and reading it back.
i am not able to read data which i am writing to it . i am posting my flash file please suggest where i...
I need to sendt several indications on one BLE_GATTS_EVT_WRITE event. If I just call sd_ble_gatts_hvx I get NRF_ERROR_BUSY Isn't it strange? API stats:
Only one indication...
Hello,
I'm a beginner and I have lots of questions. So I wanna communication with MCP4110 chip. But I can't. I configured SS, MISO and CLK pin in sdk_config.h. (SEGGER...
Hi, all,
I try to use NRF52832 as central and peripheral. When it is connected with peer as central, I try to send to peer a message with "sd_ble_gattc_write", but I can...
Hello,
I have enabled WDT for nrf52810,S112 with following configuration.
static void System_task_initWatchdog(void) {
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Pause << WDT_CONFIG_HALT_Pos...
I'm using the nRF52 DK with SDK 15.3.0. At this point I'm trying to get a UART loop back to work by tying the TX pin (P0.8) to the RX pin (P0.9). I have verified that the...
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hi,
Good Day!
Problem: We have LED Screen connected to nrf52832 through SPI com and we have some led graphic effects in our application which requires some delay between...
Hello,
I need to send logged sensor data in external flash to a phone via BLE. What is the best way to accomplish this?
How should the GATT be designed for transferring...
