Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I'm using an NRF52840 custom board along with FreeRTOS and soft-device S140 V6.0.
I want to access the complete 256KB of RAM for verification of RAM using a custom protocol...
Hi I'm considering a design with this precision RTC
I intend to use the 32KHz output on XL1 (and XL2 grounded) as I've seen done here, but the DS3231 datasheet says the...
On both the 51 and the 52, I believe the reset pin is active low, and should otherwise be tied to VDD?
The reason I am asking is that I failed to find this information...
Configuring the GPIO with the following parameters giving me the 3.3 volts on the pin 26.
Is there any way to bring the voltage down to 1.8V through software ?
Hi, I am currently working in Matlab to develop my DSP algorithms and will use the Matlab coder and Embedded coder to convert them to C code. Afterwards I will import the...
Hello,
I am currently trying to build the GPS sample from the latest Code Version. I am using SES on a Windows machine. After starting the build process I have got the...
Hello,
I've been using NRF Connect on Windows for a 3 or 4 months now. During the startup I get a window that reads
Unable to download latest app info: Unable to download...
Hello everyone,
I got a problem with receiving an array data on Android application sent from a custom characteristic.
Below is the code for sending an array data via...
I have been using my 2 nrf52840 DKs now for a while and have been loading and changing the light switch mesh example quite a bit. I have also been using the 840DKs to load...
Hello!
I want the device to immediately stop any data transfer when it receives an external event, stop sending advertising and go to sleep.
How to do it right? After...
Hi Folks,
Can you please let me know if nRF52811 supports XIP (Execution in Place) feature where I can use SPI NOR Flash to the SoC and execute my code directly from Flash...
SDK 15.2
Mesh SDK 3.1.0
Base Example: Enocean_Switch
Im working on creating an LED dimming firmware that uses a long press on the Enocean remote to dim the LED. It works...
Hi there, I tested range on NRF52840 with Thread SDK, so I have got small enough range. The test has been performed indoor, power transmission 0dBm, the range result is 10m...
Hi. In our application we are reading the voltage on 3 Analog input pins via saadc. System is also a BLE central and UBD CDC device so lots going on.
Quite often the 3 analog...
We have a requirement for the ble-peripheral device that we are designing to be able to be "registered" to a user through their iphone. If that user has multiple iOS devices...
