if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hello,
I want to create an application for the nRF52832 using Segger Embedded Studio and the nRF-SDK. In order to have a clean and portable solution I would like to have...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor...
I'm using the UART / Serial Port Emulation over BLE example on the nRF52 development kit connected to a custom microcontroller.
I just need the nRF52 to simply relay bytes...
Hi everyone,
I have been looking for information about this, but I have not been able to find anything. I would like to send data employing UART, but I can not use the...
Hi, I have a few general questions on nus_data_send().
First off, is there another known way of transferring an array/string via ble to the Nordic mobile app other than...
Dear Sir,
I am working with nrf52832, SDK15 and s132 soft device.
I am using RIGADO DK .
Is it possible to continue advertising(from peripheral device) even after...
Hi All
I am doing a project which is base on SDK15.2 examples\proprietary_rf\gzll\gzp_dynamic_pairing\host\pca10040\blank\arm5_no_packs
I would like to add a timer to...
Hello,
I cannot add SPI0 to my application because OpenThread library was built with it without any interest of that. Could you fix it please ? (I need the 3 SPI peripherals...
Hello! I want to use the start time of the XOSC16M in NRF24LE1. I got ~4 ms. Can I put the processor to sleep at this time in standby mode? How to do it to wait for wakeup...
Hi all:
I see the "ant_share_channel _master_to_master" example,
this example is share_master,
my question is,
How to get p_ant_message[]?
the p_ant_message[]...
Is the recently released SoftDevice - ANT/BLE S332 SoftDevice v6.1.0 - compatible with the recently released SDK v15.2.0 ?
The supported SoftDevices listed in the documention...
Hello. A re-connection failure problem happens on our products.
chip:nRF52832 SoftDevice:S132 SDK v11.0
1. pairing and bonding on LESC 2. reset connection and re-connect...
Hi,
I have connected and SPI flash module to my pca10040 dev board. I wrote a test cycle of erase/write/verify for the entire flash and it works correctly. My initial pinout...
