Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi, everyone,
We are developing the BLE project on nRF52832 chip by using RTT / UART logging. Previously we monitored the project via UART communication port. But than we...
Dear Team,
Can you please review the attached schematic of NRF51822 used with matching Balun and chip antenna.
Balun: 2450BM14E0003T
Chip Antenna: 2450AT18A100E...
I have an application running on an nRF52 with the S332 softdevice which is a server which exposes a a few services each with a few characteristics. I am using the Nordic...
Can the nRF2460 be operated with TXLAT (0x52) set to a value lower than 4 ?
Can the nRF2460 have a lower latency than 20mS ?
The range requirements are very small (30...
Hi All,
I have created a custom board header file based off of the pca10040.h file. I have customised this to support 10 buttons and 2 leds. I have also extended the array...
Hi everyone ;)
I have a problem with timeslot ESB library with Bluetooth LE. In my application i need do somethingh like that:
Bluetooth and ESB PRX works excelent...
Hi, I am using the BLE mesh 2.2.0 with nRF5_SDK_15.0.0_a53641a. I am using Segger embedded studio as toolchain. I was able to compile and flash the default app code onto NRF52...
I am working on an application to connect approximately 500 devices in a single network... trying to check if Thread or Mesh is a better option... Please do suggest...
After searching around a little bit I found this post, but sadly an answer did never come up apparently. I'm using the nrf52 DK, using the 132 Softdevice.
I'm kind of at...
Hi every one!
I have nRF52840 dongle and BMD-300 Series Evaluation kit featuring the nRF52832.
I`d like to transmit continuous signals from nRF52832 to dongle(Desktop...
I have two ble boards（board A and B）, one for client(Board A) and the other serve as slave(Board B). now i want to use board A to upgrade the application of board B by OTA...
Hi,
i would like to use the Power Profiler v2.0.0 from nRF Connect Software. The Power profiler is connected and it works with the Software 1.0.0. When i launch the power...
Hello,
I want to configure de coded mode on my nRF52DK, using the ble_app_interactive. How can I do it ?
I've saw that I can set the coded mode by de CENTRAL to a PEROPHERAL...
Hi,
I designed my custom board with RF52832. I was able to detect my board using the debugger.
I am using the BLE mesh default "Light switch proxy server".
I could get...
